How big can an embroidery design be on a cap?
Height limits by crown profile from two embroidery educators, cap frame fields from five machine makers, and the measuring rule that turns both into a number for the cap in your hand.
Quick answer
On a structured cap front, keep the design 2 to 2.25 inches tall and about 4 inches wide. On low profile or unstructured caps, keep it under 1.8 to 2 inches tall and 3.5 to 4 inches wide. For any cap, measure from the bill seam to where the crown starts to curve and subtract 1 inch. The cap frame's field is larger and is not the limit.
On this page
A cap front takes a design about 2 to 2.25 inches (51 to 57 mm) tall and about 4 inches (102 mm) wide. Low profile and unstructured caps take less height: under 1.8 inches in one educator's rule, up to 2 inches in another. The height limit comes from the cap, not the machine: every cap frame below can stitch taller than the crown allows. For mounting, backing and sequencing, start with caps and hats; this page is only about size.
Maximum height by cap profile
Two embroidery educators publish height limits by profile: Bill Garvin of BG Tech Services, in a cap webinar for the thread maker Gunold, and Judy Hahner, in BERNINA's multi-needle eBook on caps. Two print-on-demand services publish the limits they accept for orders. They line up within a quarter inch.
| Cap | Height | Width | Source |
|---|---|---|---|
| Pro style and 5-panel | Under 2.25 in | Not given | Garvin (Gunold webinar) |
| Standard cap | No more than 2.10 to 2.25 in | Set by the frame and machine | BERNINA |
| Structured cap, snapback | Up to 2.25 in | 4 to 5 in | Printful |
| Snapback, baseball, trucker | 2.25 in max | 4 in max | Bonfire |
| Structured mid profile | Under 2 in | Not given | Garvin |
| Trucker | Up to 2 in | Up to 5 in | Printful |
| Low profile | 2.0 in, usually the maximum | Not given | BERNINA |
| Unstructured and low profile | Under 1.8 in | Not given | Garvin |
| Dad hat (unstructured) | 1.75 to 2 in | 3.5 to 4 in | Printful |
So the working numbers are 2.25 inches tall on a pro style or other high, structured front, under 2 inches on a structured mid profile, and 1.75 to 1.8 inches on soft, low caps. Garvin's first rule is the reason they differ: the taller the cap, the larger the design can be.
Measure your own cap: bill to curve, minus 1 inch
Profiles are not standardized between cap makers, so the table is a starting point. BERNINA gives a rule that works on any cap: measure from the bill up to the point where the front starts to curve back, and subtract 1 inch. What is left is a safe design height. Width, it says, depends on the cap frame and the machine.
The reason is mechanical. BERNINA explains that as stitching moves up the cap, the inside of the cap can brush the machine's lower arm and restrict the cap's movement, which shows as distortion and vertical lines. Higher still, the pressure of the arm against the inside can push the cap off the frame. A design that is too tall fails at the top, not the bottom.
How close to the bill can the design start?
BERNINA puts the bottom of the design 3/8 to 1/2 inch (10 to 13 mm) above the seam where the front meets the brim, because a stiff, bulky seam there deflects the needle, which shows as distortion, needle breaks and poor stitching. Garvin gives the same floor from the machine side: on most cap systems, the lowest you can sew is 0.5 inch from the strap, to allow room for the presser foot. A design placed lower is a common cause of needle breaks on caps, so trace the design before every new run.
Why the cap frame's field is not the limit
The confusion behind this question is that cap frames are sold with a stated field, and the field is taller than the advice. A frame listed at 60 or 83 mm tall suggests a 2.4 or 3.3 inch design. It is not: that is how far the frame can move, not how much of the crown is flat.
| Frame | Height | Width |
|---|---|---|
| Brother PRCF3 cap frame (PR multi-needle) | 60 mm (2.4 in) | 130 mm (about 5 in) |
| Brother PRPCF1 wide cap frame (PR1000 series) | 60 mm (2 3/8 in) | 360 mm (14 in), "virtually ear-to-ear" |
| HappyJapan Wide-Cap set (HCH, HCS series) | 67 mm (2.6 in) | 290 mm (11.4 in) |
| Tajima TMBP2-SC wide and semi-wide cap frames | 83 mm (3.2 in) | 180 mm (7.0 in) |
| Melco cap system | 83 mm maximum | 270 degrees |
Width works the other way round. The frame allows far more than the front panel shows. Garvin notes that most 270 degree frames have a 13 inch turning area, which gives 12.5 inches of sewing area once a 0.5 inch safety margin is taken off. That width is for designs that run around the sides; for the front alone, Printful and Bonfire stop at 4 to 5 inches. To compare a cap frame with a flat hoop, use hoop sizes or the hoop size checker, but check the height against the cap, not the frame.
Centering the design on the frame
Width is measured from the center seam, so placement errors show as a lopsided logo before they show as a size problem. BERNINA advises using the center seam as the start and finish point for consistent placement, and on a 270 degree frame, offsetting the center of the cap to the left when loading it, because it centers itself when clamped down. Cap frames and drivers are a multi-needle accessory; if you are weighing a machine partly for caps, single vs multi-needle covers the trade-off.
Side and back sizes
Printful publishes side and back limits that apply to any hat: side logos 2 to 2.5 inches wide and 1 to 1.25 inches tall, back logos 2.25 to 3 inches wide and 0.75 to 1 inch tall. Melco notes its system can stitch the back of a cap, and that with its Fast Clamp accessory it can also reach the back, drawstring and sides. BERNINA suggests moving part of a logo to the side, back or top when it would be too small to read on the front.
Detail limits inside the size
A 2 inch tall front leaves little room for fine detail, and the curve and center seam make it worse. Printful's minimums are 0.25 inch letter height and 0.05 inch line thickness, with hat logos typically capped around 15,000 stitches. Bonfire sets 0.25 inch text and requires negative space of at least 0.2 inch. The site's own floor for lettering is the same quarter inch capital height on 40 wt thread; lettering covers fonts and sequencing on caps, and small lettering problems covers what fails first.
BERNINA adds that most stock designs are not digitized for caps. Shrinking a chest logo to 2.25 inches tall without recalculating density makes it stiff and board-like; resizing designs explains when a resize needs the original object file. Garvin's other rule matters here too: cap frames sew caps upside down, so turn the design 180 degrees on the machine.
Size a cap design, step by step
- Identify the cap. Structured or unstructured, low, mid or high profile, five or six panel. Cap types explains the terms.
- Measure the flat height. From the bill seam at center front to where the crown starts to curve back.
- Subtract 1 inch. That is the design height. Cap it at 2.25 inches on a high structured front, 2 inches on a mid profile and about 1.8 inches on a soft, low one.
- Set the width. About 4 inches on the front panel, 3.5 to 4 on a dad hat. Wider only on a wide or 270 degree frame, with the design meant to wrap.
- Audition it full size. BERNINA recommends printing the design at 1:1, cutting it out and holding it on the cap for size and placement.
- Place the bottom 3/8 to 1/2 inch above the bill seam, and trace on the machine before stitching.
- Stitch it slower than flat goods. Speed settings gives the starting range for cap frames.
When these numbers stop applying
- Home single-needle machines. Without a cap frame the cap is hooped flat or floated, and the flat area of the front and the bill hitting the machine set the size, as flat hooping caps explains. The figures above still give a sensible ceiling.
- Beanies and knit caps. Garvin's advice is to hoop them flat. Printful accepts about 5 by 1.75 to 2 inches on beanies, Bonfire 4 by 2 inches.
- Bucket hats. Printful gives about 5 inches wide by 1.75 to 2 inches tall; Bonfire limits them to 2.5 by 2.5 inches.
- 3D puff. Foam raises every column, so leave margin under the height limit; 3D puff foam and satin settings covers the columns.
- A specific product. When a cap maker or decorator publishes a decoration area for one style, that figure wins over any general table.
Frequently asked questions
What is the maximum embroidery size on a baseball cap?
On a structured baseball cap front, about 2.25 inches tall and 4 inches wide. Bonfire limits snapback, baseball and trucker fronts at 4 by 2.25 inches, Printful allows 4 to 5 inches wide on structured caps, and BERNINA recommends no more than 2.10 to 2.25 inches tall on a standard cap.
How tall can a design be on a low profile cap?
BERNINA puts the usual maximum at 2.0 inches; Garvin's limit for unstructured and low profile caps is under 1.8 inches. Measure your cap from the bill seam to where the crown starts to curve and subtract 1 inch to check.
My cap frame says 83 mm tall. Can I stitch a 3 inch design?
Usually not on the front. The frame's field is how far the frame can move, not how much of the crown is flat. As stitching moves up the crown, the inside of the cap brushes the machine's lower arm, which BERNINA says causes distortion and can push the cap off the frame.
How far above the bill should cap embroidery start?
Start the bottom of the design 3/8 to 1/2 inch above the seam where the front meets the bill. BERNINA gives that range because the bulky seam deflects the needle, and Garvin says most cap systems cannot sew closer than 0.5 inch to the strap.
How big can a logo be on the back or side of a cap?
Printful's limits are 2.25 to 3 inches wide and 0.75 to 1 inch tall on the back, and 2 to 2.5 inches wide by 1 to 1.25 inches tall on a side.
Sources and further reading
- BERNINA: Just Embroider It! E 16, Embroider on Caps (Judy Hahner) Bill to curve minus 1 in; 2.10 to 2.25 in standard, 2.0 in low profile; 3/8 to 1/2 in above the brim seam; lower arm contact
- Gunold webinar: I Hate Hats! (Bill Garvin, BG Tech Services) Height limits by profile; 0.5 in from the strap; 270 degree frames 13 in turning, 12.5 in sewing area; designs turned 180 degrees
- Brother: PRCF3 cap frame 130 x 60 mm cap frame field, PR series
- Brother: PRPCF1 wide cap frame and driver 360 x 60 mm wide cap field, PR1000 series
- Tajima: TMBP2-SC Wide and semi-wide cap frames, 83 x 180 mm
- Melco: Embroider caps Cap field 83 mm high, 270 degrees wide; back and side stitching
- makema: HappyJapan Wide-Cap cap frame set 67 x 290 mm wide cap field, HCH and HCS series
- Printful: Hat logo size and placement guide Front, side and back limits by hat type; letter, line and stitch count minimums
- Bonfire: Embroidery guidelines for hats 4 x 2.25 in cap front, beanie and bucket hat limits, text and negative space minimums
Found something wrong or out of date? Tell us and we will fix it.