How to embroider a design larger than your hoop
Splitting by the stitch-light line or a straight cut, how much overlap to set, alignment marks against printed templates, the stabilizer that stops the fabric moving, and when a multi-position hoop is the better buy.
Quick answer
Split it in embroidery software into parts that each fit your hoop, with an overlap between them. mySewnet defaults to 50 mm. Let the software route the split through the lightest stitching, and turn on alignment marks. Bond the fabric to sticky or mesh cutaway backing, stitch the parts in their numbered order, and stop the machine at once if the first marks of a new part miss the last ones.
On this page
- Key takeaways
- How each program splits and marks the parts
- Split along the stitch-light line, not a straight cut
- How much overlap to set
- Alignment marks and printed templates
- Stop the fabric shifting between hoopings
- Stitch the parts in order
- When the first dots miss: stop
- Worked example: a 120 x 300 mm design in a 5x7 hoop
- The alternative: a multi-position hoop
- What this does not cover
Key takeaways
- A design larger than the hoop is stitched as a split design: software cuts it into parts that each fit the hoop, and you rehoop between parts.
- Set an overlap between hoop areas. mySewnet defaults to 50 mm, allows 9 mm up to half the hoop's shortest side, and routes the split line through the fewest stitches.
- Turn on alignment marks before you split. Each part ends with marks, and the next part starts with marks in the same place.
- Bond the fabric to the backing every time: sticky-back stabilizer, or mesh cutaway with spray adhesive.
- Stitch the parts in their numbered order. If the first marks of a new part miss the old ones, stop the machine before any design stitches go down.
To embroider a design larger than your hoop, split it in software into parts that each fit the hoop, then stitch the parts one at a time and rehoop the fabric between them. Small alignment stitches tie each part to the last. Software makers call this multi-hooping or a split project. Before you split, check the real size against your hoop's sewing field, the area the needle can reach. Hoop sizes lists those fields, and the hoop size checker tells you whether a design fits at all.
Four terms carry the rest of this page:
- Overlap: the strip of fabric two neighboring hoop areas both cover. The split has to happen inside it.
- Split line: where one part's stitches stop and the next part's start.
- Alignment marks: a few small, loose stitches at the end of one part and the start of the next. Software calls them alignment stitches, aligning stitches or registration marks. If both sets land on the same spot, the parts will meet.
How each program splits and marks the parts
The method is the same everywhere; the settings and names are not. Each row is explained below.
| Software or source | How it splits | Overlap | Alignment marks |
|---|---|---|---|
| mySewnet (Split Project) | Intelligent (fewest stitches cut) or Straight Line (across the middle of the overlap) | 50 mm default; 9 mm minimum; maximum half the hoop's shortest side | None, Corner (L-shaped corners of three long loose stitches) or Baste (a box of long single stitches), at the end of each part |
| Wilcom EmbroideryStudio and Hatch | Automatic, or by a split line you draw | 10 mm between sewing fields when you add hoops with the Add Hoop tools | Registration marks, 5-point or 6-point: last stitches of one hooping, first stitches of the next. Turn them on before you split |
| Embird | Interactive freehand splitting | Not given in the tutorial | Aligning stitches, horizontal, vertical or diagonal: end of one part, start of the next |
| Embrilliance Essentials and Enthusiast | Automatic, into named positions | Not given | Basting stitches added for regular hoops |
| Urban Threads pre-split designs | Split by the designer | Built into the files | Loose dots: four at the start of the first part, two at the start of each later part, plus printed templates |
Split along the stitch-light line, not a straight cut
A hoop is a rectangle, so the obvious split is a straight line. mySewnet's Straight Line "cuts straight across the center line of the overlap zone" and through anything in its way. The other choice is Intelligent. It "calculates a split line that cuts the minimum number of stitches, and minimizes cuts through solid sections." EmbroideryStudio splits by object too, or along a split line you draw with its Add Splitting Line tool. Wilcom says it splits "without additional needle penetrations", and recalculates their underlay.
Use the stitch-light line whenever the overlap gives it room. A seam through open ground has nothing to line up; a seam through a satin column or dense fill shows every fraction of a millimeter. Wilcom adds a rule for objects that overlap: "the overlapped object must be stitched before the overlapping object."
When the split cannot avoid a dense area, mySewnet changes three settings. Use Baste alignment rather than Corner. Its help says "Use Corner alignment stitches if lightly embroidered areas are split, and Baste if heavily embroidered areas are split." Set Connection to Running Stitch, not Trim, "if you have to split large stitch areas." And add Compensation, Low or High. That setting works only with Straight Line, and the higher levels are for denser designs or stretchy fabric. It works like pull compensation.
How much overlap to set
Start at mySewnet's 50 mm default. The range runs from 9 mm up to half the shortest side of the hoop, so 65 mm on a 130 x 180 mm (5x7) hoop. More overlap gives the split line more room to find a gap. In mySewnet's worked example, a 55 mm overlap moved the line clear of a flower it would have cut. The cost: each extra millimeter of overlap is one less that each new hooping adds, which can mean one more hooping.
EmbroideryStudio allows a 10 mm overlap between sewing fields when you add hoops with its Add Hoop tools. If the registration marks do not appear, Wilcom says the overlap is too small. Make the overlap bigger, or reduce the mark margin in the multi-hooping options.
Alignment marks and printed templates
You need both. The template gets the next hooping close; the marks prove it before the design stitches.
Templates. mySewnet prints a "full size template" of the split parts, "with an outline around each section to indicate how to join them together." Urban Threads uses one paper template per part. Lay its dots over the dots already stitched, tape it down, and hoop the fabric. Then "make sure the crosshairs of your hoop align with the crosshairs on your printed template exactly", and take the paper out. The template has to be full size, as mySewnet's is, or its dots will not sit on the stitches.
Marks. In EmbroideryStudio and Hatch, one set of marks is the last thing a hooping stitches, and the next set is the first thing the next hooping stitches. Hatch's help says the setting must be on "before you start the multi-hooping process", or you start over. Wilcom says the 5-point marks work on most machines and are easy to remove. The 6-point marks are sturdier, for machines that cannot stitch the 5-point kind. A larger margin puts them further from the hoop's edge: easier to align, Wilcom says, at some cost in precision. Embird's tutorial splits by interactive freehand splitting. It adds aligning stitches horizontally, vertically, diagonally or all three, at the end of the top part and the start of the next. You sew each part "exactly on top of the previous section". mySewnet offers None, Corner or Baste. Corner adds "small L-shaped corners of three long loose stitches", and Baste adds "a box of long single stitches". Both go at the end of each part, at the corners, "halfway across the overlap between the hoop areas." Embrilliance splits automatically into named positions, and adds basting stitches to line the parts up when you split for a regular hoop. Urban Threads' split hawk stitches four dots before its first part, and two dots at the start of each wing.
Find the true center first if the design goes on a finished item. Wilcom warns that "the center of the design will not generally coincide with the center of the first hooping." On a panel you will cut and sew later, that does not matter. On a jacket or a quilt top, it decides where the whole design lands.
Stop the fabric shifting between hoopings
The backing has to hold the fabric where the last part left it. The sources use two ways:
- Sticky-back stabilizer. Hatch's help prefers it "as it makes the process easier and faster". Wilcom's method is to line up the marks just stitched with the marks on the stabilizer, smooth the fabric onto the sticky back, and push pins through the centers of the marks to help.
- Mesh cutaway with spray adhesive. Urban Threads uses a sheer mesh cutaway, Sulky Soft 'n Sheer or Floriani No Show Mesh. It sprays the backing, smooths it onto the back of the fabric and hoops the two together. Each later part gets a fresh piece of backing. Trim the old backing around the stitched part first.
Adhesives and fusibles covers the spray and sticky products, and floating covers fabric laid on a hooped backing. Hoop firm, never stretched, as in how to hoop. Stretch stored in one hooping comes back on release, and the next part will not meet it.
Stitch the parts in order
The software numbers the parts, and the numbers are the stitch order. Embrilliance names the files by position, so "Rose.Pes" becomes "Rose Top #1.Pes" and "Rose Bottom #2.Pes". It warns: "If you embroider out-of-order you will get overlapping that is incorrect, and parts of your design will not be visible!" Hatch and mySewnet number theirs too. The order is not always edge to edge. Urban Threads starts its hawk with the body in the middle, then stitches each wing.
When the first dots miss: stop
The marks stitch first so you can catch a bad hooping while it costs nothing. Urban Threads says the new dots "should stitch pretty much exactly in the same spot as the last dots". It also says: "If your dots DON'T line up, stop your machine right away!" The dots are loose and pull out, so move the hooping and try again. Once a fill crosses the seam, the gap is stitched in.
When the job is done, remove the marks. Urban Threads rips them from the back and pulls them through on the front, which "should leave very little trace".
Worked example: a 120 x 300 mm design in a 5x7 hoop
Take a design 120 mm wide and 300 mm tall, and a hoop with a 130 x 180 mm sewing field. Suppose the hoop is used upright and the software is mySewnet. Here is how the numbers work through.
- Check the width. 120 mm fits inside 130 mm, so the design is split only top to bottom.
- Count the hoopings. At the 50 mm default, the first hooping covers 180 mm. Each later hooping adds 180 minus 50, which is 130 mm. Two hoopings reach 310 mm, which covers 300 mm with 10 mm to spare.
- Try the maximum overlap. Half of 130 is 65 mm. Each later hooping now adds only 115 mm, so two reach 295 mm. That is 5 mm short, and it takes a third hooping.
- Place the split. At 50 mm, the overlap strip runs from 130 to 180 mm up the design. Intelligent split looks there for the lightest path. Corner marks go halfway across it, at about 155 mm.
- Find the true center. The whole design's center sits at 150 mm. The first hooping's center sits at 90 mm. Mark the item at 150 mm, not 90, if the design is centered on something.
- Stitch and check. Stitch part 01 on bonded backing. Rehoop for part 02 with the template. Watch its first marks, and stop if they miss.
The alternative: a multi-position hoop
A multi-position hoop holds the fabric once and moves to two or three sewing areas on its own brackets. Embrilliance says that with these hoops "you only hoop the fabric once", and alignment "is accomplished automatically". Wilcom lists these:
| Hoop | Size listed (W x H) | Positions |
|---|---|---|
| Brother and Baby Lock Jumbo Small | 100 x 172 mm | 3 |
| Brother and Baby Lock Extra Large | 130 x 300 mm | 3 |
| Janome and Elna Hoop MA | 200 x 280 mm | 2 |
| Brother and Baby Lock rotating | 360 x 360 mm | Rotating |
| Husqvarna Viking and Pfaff rotating | 350 x 360 mm | Rotating |
If you split long designs often and your machine takes one of these, buy the hoop. Rehooping, templates and marks are then not needed. If you split once in a while, or the design is bigger than any hoop your machine takes, split it.
What this does not cover
These steps come from four software makers and one design seller. They do not cover machines with their own positioning features: mySewnet's examples point to Corner marks for machines without them, so check your manual if yours has one. No source gives a tolerance for how close the marks must land. "Pretty much exactly" is the standard, and your eye judges it. A split cannot fix a fabric that stretches or creeps between hoopings, which shows as the design distortion any single hooping can have. For designs bought already split, the designer's order, backing and templates come first. And if the design is only a little too big, shrinking it may be simpler: resizing designs says how far that is safe.
Frequently asked questions
Can I embroider a design that is bigger than my hoop?
Yes, by splitting it. Embroidery software cuts the design into parts that each fit the hoop, with an overlap between them, and you rehoop the fabric between parts. Alignment marks stitched at the end of one part and the start of the next show whether the hooping is right.
How much overlap should a split embroidery design have?
mySewnet defaults to 50 mm and allows 9 mm up to half the hoop's shortest side. EmbroideryStudio allows 10 mm between sewing fields when you add hoops with its Add Hoop tools. More overlap gives the split line more room to avoid dense stitching, but each hooping then adds less length.
What stabilizer is best for multi-hooping?
One that bonds the fabric so it cannot move when you rehoop. Hatch's help prefers a sticky-back stabilizer. Urban Threads sprays a sheer mesh cutaway and hoops it with the fabric, using a fresh piece for each part. See adhesives and fusibles.
What do I do if the alignment stitches do not line up?
Stop the machine before any design stitches go down. The marks are loose and pull out, so remove them, move the hooping and start that part again. Urban Threads says the new dots should land in pretty much exactly the same spot as the last ones.
Is a multi-position hoop better than splitting a design?
For long designs you stitch often, yes, if your machine takes one: you hoop once and the hoop handles the alignment. For a one-off, or a design larger than any hoop your machine takes, splitting is the way.
Sources and further reading
- mySewnet: Split Project Examples Intelligent split, 50 mm default overlap (55 mm in one example), Corner alignment, Trim connection, full size template with joining outlines, numbered files
- mySewnet: Split Embroidery options Intelligent vs Straight Line; overlap 9 mm to half the hoop's shortest side; Corner and Baste marks halfway across the overlap; Compensation with Straight Line only
- mySewnet: Using the Split Project Assistant Corner for lightly embroidered splits, Baste for heavy ones; Running Stitch connection across large stitch areas
- Urban Threads: Using alignment stitches Dots and printed template method, mesh cutaway with spray adhesive, stop if the dots miss, removing the dots
- Embird: Aligning stitches tutorial Aligning stitches at the end of one part and the start of the next; sew each part on top of the previous marks
- Wilcom EmbroideryStudio: Multi-hoop production Parts stitched after rehooping; the design center is not the first hooping's center
- Wilcom EmbroideryStudio: Adding registration marks 5-point and 6-point marks, margin trade-off, sticky back and pins through the marks
- Wilcom EmbroideryStudio: Multi-hooping characteristics Splitting without extra needle penetrations, underlay recalculated, overlapped object stitched first
- Wilcom EmbroideryStudio: Create manual multi-hoopings 10 mm overlap between sewing fields; missing marks mean too little overlap
- Wilcom EmbroideryStudio: Multi-position hoops Multi-position and rotating hoop sizes and positions by brand
- Embrilliance: Multi-Position Hooping (Essentials, Enthusiast) Hoop once with multi-position hoops, virtual hoops, basting stitches for regular hoops, stitch order warning
- Hatch Embroidery: Tips for multi-hooping and sewing out Sticky-back stabilizer, registration marks on before splitting, margin
Found something wrong or out of date? Tell us and we will fix it.