How do you make the back of machine embroidery less itchy?
Fusing settings from four makers' own instructions in one table, why they do not agree, how big to cut the piece, and when a soft mesh cutaway is the better fix.
Quick answer
Fuse a soft cover backing over the back of the finished embroidery, rough adhesive side down, using the setting for your product: Madeira Comfort Wear 150 to 160°C, 2 to 4 bar, about 15 seconds; Cover-A-Stitch 250 to 270°F, about 15 seconds. Cut it 1 cm beyond the stitching on every side with rounded corners, and let it cool before you move it.
On this page
Yes: fuse a soft cover backing over the back of the design once it is stitched. A cover is a thin, soft knit or weave with heat-activated adhesive on one side, sold for exactly this job: Madeira Comfort Wear, AllStitch Cover-A-Stitch, Superpunch Cloud Cover Stitch and Sulky Tender Touch. It puts a smooth layer between the skin and the bobbin threads, knots and trimmed backing edges that cause the itch. The part people get wrong is the heat, because these products do not share one setting.
Fusing settings by product
Every figure below comes from the maker's own instructions. Where a maker gives no figure, the cell says so rather than borrowing one from another product.
| Product | Heat press | Household iron | Time | Cut and trim | Finding the fusible side |
|---|---|---|---|---|---|
| Madeira E-ZEE Comfort Wear | 150 to 160°C (302 to 320°F), 2 to 4 bar | Two dots, maximum steam and pressure | About 15 s (press), about 30 s (iron) | 1 to 2 cm larger than the design, corners rounded | Rougher and shinier side |
| AllStitch Cover-A-Stitch (Silky Finisher, 1.3 oz) | 250 to 270°F (121 to 132°C) | Wool setting | About 15 s | Not given | Hold it to the light: the fusible side has a glimmer |
| Superpunch Cloud Cover Stitch (56 g/m² polyester circular knit) | 230 to 266°F (110 to 130°C) press temperature, 240 to 275°F (115 to 135°C) at the fuse line, 3 to 5 bar | Not given | 10 to 13 s | Not given | Not given |
| Sulky Tender Touch (knit mesh) | Not given | Iron it on with steam | Not given | Cut with pinking shears | Not given |
Cloud Cover's figures come from the instruction sheet on Superpunch's product page, written for an electric conveyor press; its steam press column is marked N/A. Some retail listings give a single 260°F, which sits inside that range but is not the maker's figure. Sulky's settings come from its own blog post on the product, which gives method (steam, pinking shears) but no temperature.
Why the temperatures do not agree
Two answers circulate for "what heat does a cover backing need": a hot setting around 150 to 160°C, and a moderate one around 120 to 130°C. Both are right, for different products. Madeira's adhesive is specified at 150 to 160°C. Cover-A-Stitch and Cloud Cover are specified 20 to 40°C lower, and Superpunch describes Cloud Cover as bonding "at a moderate temperature". The confusion comes from treating "cover backing" as one material. It is a category, and each adhesive has its own window.
So use the setting for the product in your hand, and treat the hot end as a ceiling rather than a target. Madeira states the limit plainly: heating above 160°C for more than 30 seconds might harm the materials. That matches the thread side too. Two dots on an iron is a sole plate of at most 160°C, the ceiling for polyester and rayon embroidery thread on our thread wash and iron temperatures page. Metallic thread is held to one dot, at most 120°C. None of the four covers publishes a setting at or below that except the bottom of Cloud Cover's press range, so on a design with metallic thread, fuse a test piece over the metallic area on a scrap first.
How big to cut the cover
Madeira says to cut the piece 1 to 2 cm larger than the embroidered design, with rounded corners. Its wording does not say whether that is per side or overall. Cutting 1 cm beyond the outermost stitches on every side satisfies both readings: it is 1 cm per side, and 2 cm larger overall. That margin also needs to clear the trimmed edge of the backing underneath, since a cutaway edge is one of the things the cover is there to hide.
Round the corners on every product, not only Madeira's. A square corner is the first place a fused piece starts to lift, and a lifted corner rubs more than the stitches did. Sulky's fix for covers that come off in the wash points the same way: cut Tender Touch with pinking shears and iron it on with steam, so the edge has more grip. Sulky's answer in the post's comments adds a grain rule: lay the cover with its stretch running the same way as the shirt's if you want the area to keep some stretch, and across it if you want less.
Fuse it, step by step
- Finish the back first. Trim jump threads and the cutaway or tearaway as you normally would. The cover goes on last.
- Turn the garment inside out so the back of the embroidery faces up.
- Cut the cover 1 cm beyond the stitching on every side, corners rounded, or with pinking shears for Tender Touch.
- Find the adhesive side. On Comfort Wear it is the rougher, shinier side; on Cover-A-Stitch, hold it to the light and look for the glimmer. Place it adhesive side down on the back of the stitching.
- Protect the front. Madeira recommends a clean cloth under the front of the embroidery, between it and the press or ironing board.
- Fuse at your product's setting from the table: on a press (the same one used for heat press patches), the stated temperature, pressure and time; with an iron, set it down and hold, as the adhesives and fusibles guide describes, rather than sliding it.
- Let it cool before you move the garment. Madeira says so explicitly; the bond is not finished while the adhesive is warm.
- Check the edges. Run a fingernail round the rim. A corner that lifts gets another few seconds of heat, not a higher temperature.
When to use soft mesh cutaway instead
A cover and a backing do different jobs. The backing supports the stitches while they are made and, for cutaway, for the life of the garment. A cover goes on after stitching and supports nothing during it: Superpunch's product page says plainly that Cloud Cover "is not a stabilizer". So the cover never replaces the right backing from stabilizer types. The question is whether the backing alone can be soft enough that you do not need a cover at all.
Choose a soft mesh (no-show) cutaway as the backing, and skip or add the cover by these rules:
- The itch is the backing, not the stitches. If the wearer feels a stiff patch with a hard edge, the cutaway is too heavy for the job. Sulky describes its Soft 'n Sheer mesh cutaway as "very soft, soft enough for a baby's skin" and recommends it for knits. Changing the backing grade fixes this at the source; a cover only hides a stiff edge behind another layer.
- The fabric cannot take the heat. If a hidden test shows the fabric glazing or marking at the cover's setting, Madeira's own instruction is to make sure the fabric withstands the temperature. Do not fuse. Use a non-fusible soft mesh cutaway and trim it with the same rounded corners.
- You are planning the garment, not rescuing it. On lightweight knits for children or sensitive skin, start with soft mesh, as t-shirts and knits recommends for light tees. Add the cover afterwards only if the bobbin side still rubs.
- The design is dense. A cover does nothing for a stiff fill. Sulky positions its fusible Soft 'n Sheer Extra for dense designs; heavier support or a lighter stitch density is the fix, and the cover is optional on top.
The two are not either or. On baby wear and next-to-skin knits, soft mesh behind and a cover over it is the most comfortable back you can make. The stabilizer picker gives the backing; this page covers the layer that goes on after.
Where these settings stop applying
- A product not in the table. Use its own maker's figure. If it has none, test at a moderate setting first; do not borrow Madeira's 150 to 160°C, the hottest window here.
- Fabrics that should not be fused. Vinyl, faux leather, velvet and other napped fabrics, and anything labeled do not iron. The fusibles section lists them.
- Puckers or rippling. A cover will not flatten a design that puckered in the hoop; see puckering.
- Wash life. Madeira says Comfort Wear's adhesive reactivates each time the garment is ironed, so it stays on longer than comparable products; that is the maker's claim, not a test we ran. For any cover, a lifted edge after washing usually means it was not bonded well enough, Sulky's diagnosis too. Re-press it.
- The trim margin. No maker other than Madeira publishes a trim margin. The 1 cm per side here is Madeira's figure applied to all four, not a value the other three state.
Frequently asked questions
What temperature do you iron on an embroidery cover backing?
It depends on the product, and the makers publish it: Madeira Comfort Wear 150 to 160°C (two dots with maximum steam on an iron, about 30 seconds), Cover-A-Stitch 250 to 270°F (wool setting, about 15 seconds), Superpunch Cloud Cover 230 to 266°F on a press for 10 to 13 seconds. Sulky gives no temperature for Tender Touch, only steam.
How much bigger than the design should the cover be?
Madeira says 1 to 2 cm larger than the design, with rounded corners. Cutting 1 cm beyond the outermost stitches on every side meets either reading of that. Use pinking shears on Sulky Tender Touch, as Sulky recommends.
Does a cover backing replace the stabilizer?
No. It goes on after stitching and supports nothing while the design is made; Superpunch says outright that Cloud Cover is not a stabilizer. Hoop the usual backing, usually a cutaway on knits, and add the cover on top of it.
Why does my cover backing come off in the wash?
Usually it was not bonded well enough. Sulky's fix is to cut Tender Touch with pinking shears and fuse it with steam. Check that the adhesive side was down, the setting matched your product, and the piece cooled before it was moved, then re-press any lifted edge.
Is soft mesh cutaway enough on its own for sensitive skin?
Often, on light designs. Sulky describes its Soft 'n Sheer mesh as soft enough for a baby's skin. If the bobbin side of the stitches still rubs, fuse a cover over it as well.
Sources and further reading
- Madeira: How to use Comfort Wear to soften the back of embroidery (PDF) Press 150 to 160°C, 2 to 4 bar, about 15 s; iron two dots, maximum steam, about 30 s; 1 to 2 cm larger, rounded corners; above 160°C for over 30 s might harm
- Madeira: How to fix soft embroidery inlays Same settings on the web; rougher, shinier side down; clean cloth under the front; cool before moving
- AllStitch: Cover-A-Stitch Silky Finisher 250 to 270°F, wool setting, about 15 s; fusible side glimmers in the light
- Superpunch: Cloud Cover Stitch and instruction sheet 56 g/m² polyester circular knit; press 230 to 266°F, fuse line 240 to 275°F, 10 to 13 s, 3 to 5 bar; not a stabilizer
- Sulky blog: The Stabilizer Series, Sulky Tender Touch Cover-a-stitch use; steam and pinking shears; grain direction
- Sulky: Tender Touch and Soft 'n Sheer Extra product pages Tender Touch a permanent lightweight iron-on knit mesh; Soft 'n Sheer Extra for dense designs
- Sulky Answers: Stabilizer for machine embroidery on knits Soft 'n Sheer cutaway, soft enough for a baby's skin
Found something wrong or out of date? Tell us and we will fix it.