How far below the collar does embroidery go on a hoodie or sweatshirt?
Center chest, full back, sleeve and cuff figures from six placement guides, converted to one reference point so they can be compared, with the size limits the hood and kangaroo pocket set.
Quick answer
For a center chest design on a hoodie or sweatshirt, put the top of the design 3 to 3.5 inches below the bottom of the neckband or hood seam and keep 1 inch clear above the kangaroo pocket. On the back, start the top about 5 inches below the hood seam so the hood does not cover it. Upper sleeve logos go 4 to 4.5 inches below the shoulder seam.
On this page
Placement figures for hoodies look contradictory because they measure different things: to the top of the design or its center, from the neck seam, the shoulder seam or "the top of the jacket". Put on one reference (the neckband or hood seam at center, measured to the top of the design), Embroidery Library, Stahls, RGR Embroidery, Embroidery Legacy, Printful and Brother agree closely.
The measurements on one reference point
Measure flat and unstretched, down the center line. These are starting points for an adult large, not a standard.
| Location | Measure from | Figure | Where it comes from |
|---|---|---|---|
| Center chest (crew or pullover hoodie) | Bottom of the neckband, or the hood seam, at center front | 3 to 3.5 in to the top of the design | Stahls (sweatshirts); Brother uses 3 in. Embroidery Library gives 3.5 to 4.5 in from the garment neck |
| Left chest | Where the left shoulder seam meets the collar | 7 to 9 in (men), 5 to 7 in (women) to the center | Same figures as shirts; see left chest placement |
| Full back, sweatshirt | Collar at center back | 5 in to the top | Embroidery Library (shirt backs) |
| Full back, hoodie | Hood seam at center back | 5 in to the top; 5.5 in on a full-zip worn open | Embroidery Library, Printful, screen printers' practice (below) |
| Jacket back | Collar seam at center back | 6 to 9 in to the center (Stahls); 10 in to the center, men's (Embroidery Legacy) | Center figures: they land where a 5 in top lands on a tall design |
| Upper sleeve | Shoulder seam | 4 to 4.5 in down, centered on the shoulder seam line | RGR Embroidery; sleeve designs 3.5 in wide or smaller |
| Ribbed cuff | Top of the cuff | About 1 in above it, opposite the underside sleeve seam | RGR Embroidery (cuff with no button) |
Center chest: 3 to 3.5 inches to the top of the design
On an adult crewneck, measure down the center front from the bottom edge of the ribbed neckband and put the top of the design 3 to 3.5 inches (76 to 89 mm) below it. That is Stahls' figure for sweatshirts, and Brother's sweatshirt monogram tutorial uses 3 inches down from the center neckline. On a pullover hoodie the hood seam is the neckline, so measure from the bottom of the hood seam at center front. Embroidery Library's 3.5 to 4.5 inches measures from the garment neck, not the bottom of the band; the starting edge moves the answer by the band's width, so write the reference point on the work order.
Center chest figures run to the top because designs vary so much in height: anchoring the top keeps the gap under the neck constant, and a taller design grows downward. Left chest figures run to the center, which is why the two sets look unrelated. The t-shirt guide gives the same rule (three finger widths below the neckband) and the same warning: a shirt marked while pulled long ends up with the design low once it relaxes.
How big can a center chest design be on a hoodie?
On a hoodie the kangaroo pocket sets the height. Rush Order Tees advises at least 1 inch between a logo and any hem, edge, pocket or structured area, and Printful warns against stitching across the pocket opening or seams. So measure from the hood seam to the top of the pocket, subtract the 3 inch gap at the top and 1 inch of clearance at the bottom, and what is left is the tallest design that fits. If your tape reads 12 inches to the pocket, that is 8 inches of design height.
Width is a hoop question. RGR Embroidery's ceiling for full front and back designs is 11 by 11 inches, run in Tajima 21, 24 and 30 cm hoops. On a home machine, an 8x8 field is really 200 x 200 mm (7.9 in), so anything wider needs an 8x12 class field or larger; hoop sizes lists the real fields and the hoop size checker tells you whether a design loads. The "4 x 4 inch maximum" for center chest embroidery that appears in some hoodie guides is one print-on-demand seller's product limit, not a garment rule.
Zip hoodies
A center chest design cannot cross a zipper. Printful says it may need resizing or moving on a zip-up, and Garment Printing says zip-up logos usually go off-center or split across both sides. The usual answer is a left chest logo at the normal shirt figures, with its bottom edge clear of the pocket.
Full back: start about 5 inches below the hood seam
On a sweatshirt, Embroidery Library puts the top of a back design 5 inches below the collar, centered between the side seams. On a hoodie the hood lies over the upper back, and Printful advises placing the design low enough to stay visible below it. Screen printers on The Shirt Board describe the trade-off: one places a 12 inch tall hoodie back 4.5 inches below the seam on a large and tends to drop it another half inch, noting the hood does not hang as low as people fear; another warns an unzipped full-zip hood hangs a lot lower; a third had customers ask for a lowered print to be moved back up.
So on an adult large the top goes 5 inches below the hood seam at center back, 5.5 inches on a full-zip worn open, and no lower.
Why jacket back figures say 7 to 10 inches
Stahls places jacket backs 6 to 9 inches from the collar seam to the design's center. Embroidery Legacy centers a men's jacket back 10 inches below the collar (9 to 10 for women's, 5 to 7 for children's). Those are center figures, and they describe the same spot as a 5 inch top: a 10 inch tall design whose top sits 5 inches down has its center at 10 inches. Embroidery Library's adult 7 to 9 inches from the shoulder seam does not say top or center. Set the top first, then check: for a full back 9 to 11 inches tall, the center lands roughly 9.5 to 10.5 inches below the seam.
Size changes the file too. Embroidery Legacy contrasts 0.30 mm tatami spacing on small designs with spacing as open as 1.0 mm for layered color on large ones, and advises cutaway and hooping rather than floating, because a floated item can shift over a stitch-out that runs for hours. Scaling a left chest logo up to a back is covered in resizing designs, and why heavy fills stiffen fleece is in stitch density.
Sleeves and cuffs
RGR Embroidery places an upper sleeve logo on a long sleeve 4 to 4.5 inches down from the shoulder seam, centered on the shoulder seam line, and keeps sleeve designs 3.5 inches wide or smaller. On a cuff with no button, which covers a hoodie's ribbed cuff, it goes about 1 inch above the cuff, centered opposite the underside sleeve seam. A sleeve rarely fits a flat hoop on a home machine; a small hoop or floating on sticky stabilizer is the usual workaround.
How to mark a hoodie, step by step
- Lay it flat and relaxed. Front up, hood folded behind, smoothed without pulling.
- Find the center line. Fold lengthwise and crease, or measure between the side seams, and mark down from the hood seam.
- Mark the top of the design. 3 to 3.5 inches below the bottom of the neckband or hood seam for a center chest; 5 inches below the hood seam on the back.
- Lay a full-size paper template on the mark, printed from your software as Embroidery Library recommends, and check the 1 inch pocket clearance.
- Hold it up by the shoulders. Adjust now, not after hooping.
- Hoop with the right backing. Sweatshirt fleece takes 2.5 to 3 oz cutaway, with a film topper on brushed fleece or small text, per the stabilizer chart. Set the hoop screw to the full thickness or use a magnetic hoop, as how to hoop explains, and watch for hoop burn on dark fleece.
- Trace before you stitch so the needle path clears the hoop and lands on your marks.
When these numbers stop applying
- Children's garments. Embroidery Library's children's guide gives shirt-front tops of 1.5 to 3 inches and 3 to 4.5 inches below the neck, and shirt backs of 2 to 4 and 3.5 to 5 inches. Its two size headings appear to be swapped (onesie figures sit in the 4 to 16 table), so read the smaller figures as the infant and toddler ones.
- Oversized, cropped and women's cuts. No source gives separate center chest or back figures; mark the starting figure and judge it held up.
- Print guides. Many hoodie pages are written for screen print or DTG, with front art 10 to 13 inches wide. Embroidery at that size is a hoop and stiffness question first.
- Taste. Embroidery Library says correct placement depends largely on individual taste.
Frequently asked questions
How far down from the collar should a center chest design be on a sweatshirt?
Put the top of the design 3 to 3.5 inches below the bottom of the ribbed neckband, centered. Embroidery Library's figure of 3.5 to 4.5 inches measures from the garment neck itself, so it starts higher and runs longer. The figure is to the top of the design, not its center.
Where does a back design go on a hoodie so the hood does not cover it?
Start the top of the design about 5 inches below the hood seam at center back on an adult large, or 5.5 inches on a full-zip worn open. Going lower risks a design that looks too low with the hood down; one print shop's customers asked for exactly that to be moved back up.
How big can a center chest embroidery design be on a hoodie?
Measure from the hood seam to the top of the kangaroo pocket, subtract 3 inches for the gap at the top and 1 inch of clearance above the pocket. Contract shops cap full front designs around 11 by 11 inches; on a home machine the hoop field is usually the real limit. See hoop sizes.
Why do jacket back placement guides say 7 to 10 inches?
Those figures run to the center of the design, or from the shoulder seam. A 10 inch tall design whose top sits 5 inches below the collar has its center at 10 inches, so the figures describe the same spot.
Where does a sleeve logo go on a hoodie?
On the upper sleeve, 4 to 4.5 inches below the shoulder seam, centered on the shoulder seam line, and no wider than about 3.5 inches. On the cuff, about 1 inch above the rib, opposite the underside sleeve seam.
Sources and further reading
- Embroidery Library: Embroidery placement guide Shirt fronts: top of design 3.5 to 4.5 in from garment neck; shirt backs 5 in from collar; jacket backs 7 to 9 in from shoulder seam
- Embroidery Library: Placement guide for infants, toddlers and children Children's shirt front, back and jacket back figures to the top of the design
- Stahls: Design placement tips Sweatshirts: top of design 3 to 3.5 in below the neck edging; jacket backs 6 to 9 in collar seam to design center
- RGR Embroidery: Garment locations, hoops and logo sizing Upper sleeve 4 to 4.5 in below shoulder seam; cuff 1 in above; full front and back 11 x 11 in; hoop sizes by location
- Embroidery Legacy: Large embroidery designs Jacket back centered 10 in below the collar (men), 9 to 10 in (women); density, cutaway and hooping for large designs
- Printful: Hoodie logo placement guide Back designs below the hood; pockets, seams and zippers
- Brother: DIY monogrammed sweatshirts Center front monogram about 3 in down from the center neckline
- The Shirt Board: Position of print on hoodie back Printers' practice: 4.5 in below the seam on a large, full-zip hoods hang lower
- Rush Order Tees: Logo placement for business clothing At least 1 in between a logo and any hem, edge or pocket
- Garment Printing: Hoodie logo placement guide Zip-up hoodies: off-center or split logos; its 4 x 4 in center chest embroidery limit
Found something wrong or out of date? Tell us and we will fix it.