What should the presser foot height be on an embroidery machine?
Start at 1.5 mm above the needle plate, then set it for the job: over bare fabric the foot should clear the surface by about one thread's thickness at the bottom of the needle stroke. Here is each maker's figure, the rule by material, and how to tell high from low by what the stitch-out shows.
Quick answer
1.5 mm above the needle plate is the standard on Ricoma MT machines and the default Embroidery Foot Height on Brother and Bernina. Melco sets its foot by feel anywhere from 0.5 to 3.5 mm. Whatever the number, the target is a gap of about one thread's thickness over unsewn fabric with the needle at the bottom, clearing the highest point of the design; set it lower on fleece, terry and structured caps.
On this page
1.5 mm is the number to start from. Ricoma calls 1.5 mm the standard presser foot height on its MT machines, and Brother and Bernina home machines ship with Embroidery Foot Height at 1.5 mm. But that figure is measured from the needle plate. What matters is the gap left above the fabric, and Melco's service manual gives it in one line: with the needle at the bottom of its stroke, set the foot close to unsewn fabric without touching it, leaving a gap "roughly equal to the thickness of the thread".
What the foot is doing on each stitch
An embroidery foot moves up and down with the needle. Melco describes the job as two halves: the foot stabilizes the material as the needle goes down through it, then keeps the material off the needle as the needle comes back up. The second half is the one that goes wrong. If the foot is too high, the fabric rides up with the needle, which is flagging, and the loop the hook needs forms in the wrong place. If the foot is too low, it presses on every stitch and the hoop has to drag the fabric out from under it.
That is why Melco's XT manual defines the ideal as the foot just touching the fabric at the moment the needle begins its upstroke. Every procedure below measures there, at bottom dead center.
Presser foot height by maker
Commercial machines give a mechanical range or a gauge, home machines a screen setting. Both measure from the needle plate.
| Machine | Standard or range | How it is set | Maker's note |
|---|---|---|---|
| Ricoma MT | 1.5 mm standard | Needle to its lowest point, a 1.5 mm Allen key under the foot as a gauge, loosen the screw on the presser foot driver and bring it down onto the key | Many embroiderers lower it on structured caps; if the key will not fit under the foot, it is too low |
| Melco AMAYA and EMT16X | 0.5 to 3.5 mm above the needle plate | Bottom Center in the software, then turn the eccentric gear behind the needle case by hand (easiest on needle 16) | No single number: set by feel on the hooped job, and reset when material thickness changes a lot |
| Brother home machines | 1.5 mm default | Embroidery Foot Height in the embroidery settings screen | A larger number increases the space between the foot and the needle plate; raise it for layers with thick batting |
| Bernina | 1.5 mm default, up to 10 mm | Embroidery Foot Height in the embroidery settings | Check your model's manual for its limit |
| Husqvarna Viking | No figure published | Presser Foot Height or Floating Height, plus and minus in the embroidery settings | Same principle, set on screen |
| Janome | No figure published | Spring (pogo) embroidery foot, adjusted with the screw on the foot | No fixed gap to set |
The Brother, Bernina, Viking and Janome rows come from Sweet Pea's foot height guide; Brother's own manual confirms the setting and its direction but gives no values on the page we read. The Melco and Ricoma rows come from the makers' service pages.
Touching the fabric or a thread's width above it?
Two instructions circulate, and both come from Melco. The AMAYA and EMT16X guides say to set the foot over unsewn fabric "so that it is just touching the material". The XT service manual says that over unsewn fabric the foot should come close but not touch, with a gap of about one thread's thickness, and that over a section already sewn it should barely touch the stitching.
They are the same setting. A foot that clears bare fabric by one thread thickness is exactly the foot that just touches a layer of stitching, which is what it will ride on for most of the design. The XT version is the precise one, so use it. What it adds is the rule people miss: always set the foot for the highest point in the design. If the design builds up heavy fill, stacked layers or 3D puff foam, the foot has to clear that, not the fabric you measured at the start.
The quick check from practice: with the needle at the bottom, a strand of the thread you are sewing should just slide between the foot and the bare fabric. If it is pinched, the foot is touching; if you could slide two strands side by side, it is high.
The rule by material
Thickness and squash are separate things, and they push the setting in opposite directions. A thick, firm stack needs the foot raised; a soft, springy one needs it lower than a thread gap.
| Material | Set the foot | Why |
|---|---|---|
| T-shirts, wovens, polos | One thread's thickness over the bare fabric | Thin and firm; the standard 1.5 mm usually lands close to this |
| Sweatshirts, then back to T-shirts | Reset for each | Melco's own example of a change big enough to need readjustment |
| Thick layers, batting, in-the-hoop projects, foam, PU leather | Raise until the gap is one thread over the highest point | Brother: raise Embroidery Foot Height for thick batting layers |
| Fleece and terry | Lower than the thread gap, pressing into the surface a little | Melco: for squishy materials it is often better to lower the foot a bit more and press into the material |
| Structured caps | Lower than standard | Ricoma: many embroiderers lower the height on structured caps |
On towels, Brother also recommends a water-soluble topper to keep the loops down. Towels and terry covers the rest of the setup. For caps, hooping and speed matter as much; see caps and hats.
Too high or too low: read the symptoms
| Foot is | What you see or hear | Source |
|---|---|---|
| Too high | Thread breaks; poor registration (outlines off their fills) | Melco |
| Too high | Fabric flaps or shifts with the needle (flagging), leading to registration problems | Sweet Pea |
| Too low | Louder sewing; a faint, lighter halo around the design, most visible on dark fabric | Melco |
| Too low | Puckering, thread breakage, the fabric struggling to move (drag) | Sweet Pea |
Notice that thread breaks appear on both sides. A break alone does not tell you which way to turn it, so use the signs that point one way. Fabric visibly lifting with the needle, or outlines landing beside their fills, means high. A machine that sounds harder than usual, or a pale ring pressed into the fabric around the stitching, means low. Melco notes the halo usually comes out with steam, water or a light ironing aid, Tell it from the hoop's own marks, covered in hoop burn and marks, by where it sits: the foot's halo hugs the stitching, the hoop's ring follows the hoop.
Flagging from a high foot is also a cause of skipped stitches, because the hook misses a loop formed in fabric that has lifted. On thick items, foot height is also one of the checks in needle breaking. If outlines are off but the fabric is not lifting, the foot is probably not the cause: start with outlines not lining up instead.
Set it in this order
- Hoop the real job. Melco's procedure needs the hoop and the fabric you will sew installed. Height set on an empty plate is a gauge figure, not a setting.
- Bring the needle to bottom dead center. On Melco, Bottom Center in the Head Timing tab; on Ricoma MT, the 180 degree icon for the selected needle.
- Find the highest point. Over bare fabric, set a thread's gap; if the design will build up foam or heavy layers, allow for that.
- Adjust. Eccentric gear behind the needle case (Melco), the screw on the presser foot driver against a gauge (Ricoma), or the settings screen (home machines). Then return the head to its up position before sewing.
- Adjust for the material. Lower for fleece, terry and structured caps.
- Stitch a test and listen. Watch for lifting, listen for a heavier sound, and look for a halo on dark goods. Change one thing at a time, as the Stitch-Out Tuning Method lays out.
When this does not apply
Machines with a spring (pogo) foot, such as Janome's, have no height setting on screen; the adjustment, if any, is the screw on the foot. The thread-gap rule is for feet that move to a fixed height. Foot height also cannot rescue loose hooping. If the fabric flags with the foot correctly set, the fabric is not held well enough in the hoop; see how to hoop. On multi-needle machines it is one of several per-job adjustments, with speed; single vs multi-needle lists the rest.
Frequently asked questions
What is the standard presser foot height on an embroidery machine?
1.5 mm above the needle plate on Ricoma MT machines, and the default Embroidery Foot Height on Brother and Bernina home machines. Melco machines have no fixed figure: the foot adjusts from 0.5 to 3.5 mm and is set by feel on the hooped job.
Should the embroidery foot touch the fabric?
Over unsewn fabric, almost: Melco's service manual says close but not touching, with a gap about the thickness of the thread, measured with the needle at the bottom of its stroke. Over stitching already sewn, the foot should barely touch it. Fleece and terry are the exception: lower the foot a little more so it presses into the surface.
Should I raise or lower the presser foot for caps?
Lower. Ricoma notes that many embroiderers lower the presser foot height when sewing structured caps. See caps and hats for the hooping side.
What is the white ring around my embroidery on dark fabric?
If it hugs the stitching, it is usually the presser foot set too low, pressing the fabric on every stitch. Melco lists this faint, lighter halo as a too-low symptom and says it usually comes out with steam, water or a light ironing aid. Raise the foot slightly for the next run.
Sources and further reading
- Ricoma: Adjusting the presser foot height on my MT embroidery machine 1.5 mm standard; lower on structured caps; 1.5 mm Allen key gauge at the needle's lowest point
- Melco XT tech manual: Presser foot height Gap about one thread thickness over unsewn fabric, barely touching over stitching; highest point in the design; bottom dead center; varies by machine and operator
- Melco: Presser foot adjustment (AMAYA) 0.5 to 3.5 mm above the needle plate; what the foot does; lower for fleece and terry; too high and too low symptoms
- Amaya UK: EMY16X adjusting the presser foot Same range and procedure for the EMT16X; readjust between sweatshirts and T-shirts
- Sweet Pea: Dealing with fabric thickness Brother and Bernina 1.5 mm defaults, Bernina up to 10 mm, Viking and Janome methods, too high and too low effects
- Brother operation manual: Preparing the fabric Raise Embroidery Foot Height for thick batting; larger number means more space; water-soluble topper on towels
Found something wrong or out of date? Tell us and we will fix it.