Which way does the needle go in a multi-needle embroidery machine?
Round-shank DBxK5 needles can go in at any angle, so the angle is yours to set. Here is what Melco, Ricoma, SWF and Brother each say, why a turn to the left breaks thread, and how to see 5° with a clock face.
Quick answer
On a round-shank DBxK5 head, put the long groove to the front and the scarf to the back, push the needle up as far as it goes, then turn the eye about 5° to your right. Melco accepts 0° to 20° right and never left, which causes thread breaks. One clock minute is 6°. Brother PR and home machines use flat shanks: flat side back, no rotation.
On this page
- The answer: groove front, scarf back, all the way up, eye 5° right
- What each maker says
- Why the left side is the one that fails
- The clock-face check: how to see 5°
- All the way up matters as much as the angle
- Flat-shank machines: Brother PR and home embroidery machines
- Putting a new needle in without losing the angle
- Where this answer stops applying
Ask which way a needle goes in a multi-needle machine and you get two answers: "straight, groove to the front" and "turned a little to the right". They are not rivals: one maker gives both as edges of a single range. The orientation ruled out is turned to the left.
The answer: groove front, scarf back, all the way up, eye 5° right
A commercial multi-needle head takes a round-shank needle, normally system DBxK5. A round shank has no flat side to seat it, so it will go into the needle bar at any angle and you have to set the angle yourself. The sequence Melco gives for its Amaya machines is the most complete published:
- Find the two sides. The front of the needle has a long groove (the thread guide); the back has an indented notch (the scarf) just above the eye.
- Insert it groove forward, scarf back, and slide it up into the needle clamp "as far as it will go".
- Turn the eye 5° to the right. Melco's acceptable range is 0° to 20° to the right: straight forward is fine, past 20° is not.
- Never turn it left. Melco's technical manual: "Do not tilt the needle so that the needle eye is oriented to the left. This will result in poor sewing performance (e.g., thread breaks)."
- Hold it there and tighten the set screw, then check the angle again.
"Right" here means your right as you stand facing the front of the machine.
What each maker says
The makers agree on the groove and the scarf. They differ only on whether to add the small turn, and none of them allows a turn to the left:
| Machine | Shank | Groove and scarf | Eye angle | Push up |
|---|---|---|---|---|
| Melco Amaya (XT tech manual, OS v10 help, EMT16X) | Round, DBxK5 75/11 | Long groove forward, scarf back | 5° right recommended; 0° to 20° right acceptable; never left | As far as it will go |
| Ricoma MT series | Round | Scarf toward the back | "Keep the needle eye facing forward"; no turn given | Up through the presser foot into the needle bar |
| SWF B-series (single head) | Round, DBxK5 | Groove in front, scarf in back | "Slightly to the right at a very slight angle" can help the hook catch the thread, especially with specialty threads; no figure | Completely, to the top of the needle bar hole |
| SWF K-series (multi-head) | Round, DBxK5 | Groove facing front | Not stated | Completely into the needle bar |
| Brother PR (PR1050X manual) | Flat, HAX 130 EBBR (Organ) or SCHMETZ 130/705 H-E | Flat side toward the back | Fixed by the flat; cannot be turned | Until it touches the needle bar stopper |
| Brother home machines (XE1, XE2, CX1E) | Flat | Flat side facing the back | Fixed by the flat | Until it touches the stopper |
Read the round-shank rows together and the disagreement disappears. Ricoma's "facing forward" is 0°, the edge of Melco's range; SWF's "very slight angle" to the right falls inside it. Melco is the only maker that puts numbers on it, and its range contains both. So the best single setting for any round-shank head here is 5° right: Melco's recommendation, SWF's direction, and room for error both ways. A needle aimed at 5° that ends up a few degrees off is still between 0° and 20°; one aimed at exactly 0° that ends up a few degrees off may be turned left.
The angle question only exists on round shanks. On a single-needle home machine and on Brother's PR multi-needles, the flat side of the shank goes to the back and fixes the angle for you.
Why the left side is the one that fails
The thread forms a loop beside the needle as it starts to rise, and the hook point passes behind the needle at the scarf to catch it, 0.1 to 0.3 mm away on SWF's B-series. That manual describes the small right turn as helping "the point of the hook catch the thread with greater ease during the formation of the stitch". Melco names the result of the opposite turn: poor sewing, with thread breaks as its example. Its service notes add that an incorrectly installed needle can cause thread breaks by itself.
So a needle orientation problem has a signature: it shows on one needle only. If thread breaking, skipped stitches or thread shredding follow one needle bar from color to color, check that needle's angle and depth before you touch its tension.
The clock-face check: how to see 5°
Five degrees is too small to judge by eye on something as thin as a needle. Melco's answer is a needle orientation magnet (Melco part 34274): a small cylindrical magnet that sticks to the front of the needle just above the eye, resting on each side of the groove, and sticks straight out in the direction the eye faces.
To read the pointer, Melco gives one reference: one minute on a clock face is 6°. A minute hand moves 360° in 60 minutes, so that converts every figure on this page:
| Eye angle | On a clock face | Sideways shift per 10 mm of pointer | Verdict |
|---|---|---|---|
| 0° (straight forward) | 0 minutes | 0 mm | Acceptable (Ricoma's instruction) |
| 5° right | Just under 1 minute | About 0.9 mm | Recommended (Melco) |
| 20° right | 3 minutes 20 seconds | About 3.6 mm | Limit (Melco) |
| Any angle left | Any time on the other side | Any distance to the left | Never |
The sideways shifts are plain trigonometry (pointer length times the tangent of the angle), so scale them to your pointer: a magnet standing 20 mm off the needle should have its tip about 2 mm right of straight at 5°, and no more than about 7 mm right at the 20° limit. Turn the needle until the tip sits just right of pointing straight at you, tighten, and take the magnet off before you stitch, as Melco instructs.
All the way up matters as much as the angle
SWF's manuals warn that if the needle is not inserted all the way to the top of the needle bar hole, "the timing of the machine will be off", and broken needles and thread breaks follow. That looks like a hook timing fault with a much cheaper fix, so reseat the needle before any timing check or a session with needle breaking.
Melco notes that if a needle will not go into the needle bar without significant force, there may be a burr in the needle bar hole, and the needle bar has to be replaced. Do not force it; that is a service repair.
Flat-shank machines: Brother PR and home embroidery machines
Brother's PR multi-needles do not take DBxK5. The PR1050X manual specifies household embroidery needles: the factory needle is "HAX 130 EBBR" (Organ), with SCHMETZ 130/705 H-E as a substitute, and it warns that any other needle may break the needle or thread or damage the needle-threading mechanism. HAX130EBBR has a flat-sided shank and is also sold for Baby Lock Professional 6 and 10 needle machines. With the flat side toward the back of the machine, it goes all the way up until it touches the needle bar stopper. Brother's home machines follow the same rule.
There is nothing to rotate: the flat fixes the angle. If thread breaks on one needle of a PR, look at depth, a bent or burred needle, or a needle that is not the specified system. Brother's own check for a bent needle is to lay the flat side on a flat surface and see that the gap along it is even.
Putting a new needle in without losing the angle
- Make it safe. On Amaya, move the safety grabber blade to the back and press the emergency stop first.
- Loosen the set screw about half a turn, until the old needle slides out. Ricoma warns against over-tightening it on the way back.
- Pick the new needle for the job: see embroidery needles or the needle and thread matcher.
- Insert groove forward, scarf back, all the way up, set 5° right, tighten while holding it, recheck, remove the magnet and test that needle.
Change one needle at a time so the others keep their angles; each wears on its own stitch count, as how often to change the needle explains. If a correctly seated new needle still misbehaves, change one other thing at a time, as in the stitch-out tuning method.
Where this answer stops applying
Tajima, Barudan, Happy and other commercial brands are not covered here; where your manual gives an angle, it overrides the 5° default. The 0° to 20° range is Melco's; Ricoma and SWF publish no limit, so on their heads treat 20° as the outer edge, not a target. A needle that has struck something is replaced, not re-angled.
Frequently asked questions
Which way does the scarf face on an embroidery needle?
To the back of the machine, on every machine covered here. The long groove faces the front. On flat-shank needles the flat side also faces the back.
Should a multi-needle needle be straight or turned?
Turn the eye about 5° to the right. Melco recommends 5° right and accepts anything from straight forward to 20° right; Ricoma says to keep the eye facing forward, which is the 0° edge of that range. Never turn it left.
What happens if the needle is turned to the left?
Melco says an eye oriented to the left gives poor sewing performance, with thread breaks as the example. Because only that needle is affected, the breaks follow that one needle bar. See thread breaking.
Can I rotate the needle on a Brother PR machine?
No. The PR series takes flat-shank HAX 130 EBBR or SCHMETZ 130/705 H-E needles. The flat side goes toward the back and the needle goes up until it touches the needle bar stopper; the flat fixes the angle.
How do I measure 5 degrees on a needle?
Use a needle orientation magnet, which sticks to the front of the needle and points where the eye faces. One minute on a clock face is 6°, so 5° is just under one minute right of straight, and the 20° limit is about three and a third minutes.
Sources and further reading
- Melco XT tech manual: Critical measurements, needles Long groove forward, scarf back, as far as it will go; eye 5° right recommended, up to 20° right; eye to the left gives thread breaks; DBxK5 75/11; burr in the needle bar hole
- Melco Amaya OS v10 help: Replacing a needle Safety grabber and emergency stop, half a turn on the set screw, 5° right (0 to 20°), needle orientation magnet PN 34274, remove before sewing
- Melco service: Needle replacement Magnet rests on each side of the thread guide; one minute is 6° on a clock face; an incorrectly installed needle gives thread breaks
- Amaya UK: EMT16X changing a needle Same procedure and 0 to 20° right range on the EMT16X; clock face reference
- Ricoma: MT how to install a needle Scarf toward the back, keep the needle eye facing forward, do not over-tighten the set screw
- SWF (SunStar): B-series single head user's manual Groove in front, scarf in back, fully inserted or timing goes off; a very slight angle to the right helps the hook catch the thread; DBxK5
- SWF (SunStar): K-series multi-head user's manual Groove facing front, shaft inserted completely; no angle given
- Brother PR1050X operation manual HAX 130 EBBR (Organ) or SCHMETZ 130/705 H-E; flat side toward the back, up until it touches the needle bar stopper; flat-surface bent needle check
- Brother USA: Change or replace the needle (XE1, XE2, CX1E) Home machines: flat side facing the back, pushed in until it touches the stopper
- AllStitch: HAX130EBBR needles Flat-sided shank, for Brother PR and Baby Lock Professional 6 and 10 needle machines
- AllStitch: Groz-Beckert DBxK5 needles DBxK5 is a round shank commercial embroidery needle
Found something wrong or out of date? Tell us and we will fix it.