What stabilizer do you use for free-standing lace?
One layer of heavy water-soluble film, or one to two layers of fibrous or fabric-type washaway, hooped drum tight. The film that fails is the thin topper, not film as such.
Quick answer
Use a heavy water-soluble stabilizer: one layer of a lace film such as Sulky Ultra Solvy or an 80 to 90 micron film (Badgemaster, Avalon Ultraflat), or a fibrous type: Floriani Wet N Gone, one layer for most designs, or Sulky Fabri-Solvy, two layers. Hoop it drum tight. Never use thin topper film alone. If the designer names a stabilizer, use that one.
On this page
Use a heavy water-soluble stabilizer and hoop it drum tight: either one layer of a heavy lace film, or one to two layers of a fibrous or fabric-type washaway. Both work. What fails is the thin clear film sold as a topper, and that is where the common advice "film is too weak for lace" comes from. Below are the lace stabilizers makers sell, how many layers each one takes, and the setup, rinse and stiffness decisions that go with them. For where lace sits among other techniques, see the freestanding lace section of the projects guide.
Lace stabilizers by product
Washaway comes in three forms: clear film, fibrous nonwoven and fabric-like mesh (the stabilizer types guide covers all three). For lace, the weight matters more than the form.
| Product | Type | Layers for lace | What the maker says |
|---|---|---|---|
| Sulky Ultra Solvy | Heavy film, translucent | 1 (Sulky) | "Four times as firm, thick, heavy and strong as the Original Sulky Solvy"; for "computerized lace embroidery" |
| Sulky Fabri-Solvy | Fabric-like, white | 2 for most designs (Sulky) | Has "the firmness, strength and feel of fabric"; lists lace-making |
| Floriani Wet N Gone | Fibrous | 1 for most free-standing lace | Hoop "tight as a drum"; rinse in lukewarm water |
| Madeira Badgemaster | Heavy film, 80 micron (3.15 mil), opaque | Not stated | Lists lace, Battenburg lace, free-standing lace and badges |
| Madeira Avalon Ultraflat | Film, 90 micron | Not stated | "Support for lace embroidery, if the design has been digitised for that purpose" |
| OESD BadgeMaster | Thick washaway | Not stated | "Shines" for freestanding lace; "leaves more starch behind", so the lace is stiffer |
| OESD AquaMesh Plus | Opaque mesh, adhesive coated | Not stated | Listed for sheers and low stitch count designs; OESD pairs BadgeMaster with AquaMesh "for stitch intensive designs" |
| Sulky Solvy (original) | Thin film | Not for lace alone | A topper for napped fabrics and a support for edge stitching |
Sulky's own advice is to look for what the designer recommends first, because designers "sometimes digitize for one or the other." Madeira puts the same condition on its 90 micron film. Where the design gives no instruction, Sulky's expert falls back on two layers of Fabri-Solvy, and adds that "it's likely either will work very well."
Film or fibrous: which is right?
Both, if the film is a lace film. The claim that film alone is too weak for lace holds only for the thin topper grade. One sewing-machine dealer's guide says plainly to avoid thin Solvy topping because it "won't hold up to the dense stitching of FSL designs", while the same guide recommends "thick film-like water-soluble stabilizer like Sulky Ultra Solvy" and even mixing a piece of each type. Sulky prescribes Ultra Solvy at one layer. Madeira sells its 80 and 90 micron films for lace.
The confusion persists because "film" names two very different products. The everyday clear film on a towel is a topper, made to hold loops down for one pass of stitching. A lace design puts thousands of penetrations into an area with no fabric to share the load, and a thin sheet perforates along the needle holes. Ultra Solvy is four times the original Solvy; the extra thickness is the whole difference.
So choose by two things, not by form:
- The designer's instruction. If the file says fibrous, or names a film, follow it. Density and underlying grids are set for that support.
- How stiff you want the result. Fibrous and starch-based types leave body behind if not fully rinsed. Hatch describes the fibre mesh type as made of starch, with a residue that "stiffens the lace", and OESD says BadgeMaster leaves more starch behind. For ornaments, bowls and 3D pieces, that is useful. For soft lace edging, rinse it all out.
Not every washaway is light enough to dissolve cleanly, either. Asked whether its 2 oz tear and wash-away squares suit lace, ColDesi answered that they are "too thick for standalone lace" and pointed to Ultra Solvy instead.
How many layers
Layers add thickness, so count layers against the product, not the project:
- Heavy lace film (Ultra Solvy class): 1 layer. A customer note on Sulky's page puts it simply: thicker film means no extra layers.
- Fibrous (Wet N Gone): 1 layer for most designs.
- Fabric-type (Fabri-Solvy): 2 layers for most designs.
- Dense or large designs: add support rather than speed. OESD combines BadgeMaster with AquaMesh for stitch-intensive work; WeAllSew hoops "a couple of layers" of AquaMesh Plus or BadgeMaster.
The site's stabilizer chart and stabilizer picker give the same split: one layer for light lace, up to two for dense lace.
Hoop and set up the machine
- Pick the smallest hoop the design fits. Less unsupported stabilizer means less flex. Hoop the stabilizer alone.
- Hoop it tighter than fabric. QuiltSocial's guide says "tighter than if you were stabilizing fabric"; Floriani says drum tight without stretching or distorting it. WeAllSew tightens the hoop screw "as tight as you can get it". The how to hoop guide covers the method.
- Fit a new 75/11 needle. WeAllSew warns that a dull needle "might have burrs" that damage the stabilizer; QuiltSocial's guide uses a 75/11 sharp because a finer needle leaves smaller holes. More on points and sizes in embroidery needles.
- Use the thread the design calls for, top and bobbin alike. Usually 40 wt rayon or polyester; some lace is digitized for 30 wt cotton or metallic, and QuiltSocial's guide is firm that a design calling for cotton gets cotton, not rayon. A heavier thread fills the same grid more tightly, so a swap changes the density the designer set (see thread weights). The bobbin must match the top, because both sides of lace show (see bobbin thread).
- Slow down if thread breaks. Dense lace stacks penetrations in one spot; lower the maximum speed before changing anything else (speed settings).
Rinse for soft lace or stiff lace
Trim the excess close to the stitching first, without clipping any threads. Then decide how much stabilizer to leave in.
| Result | What to do | Source |
|---|---|---|
| Soft, drapey lace | Rinse under warm water for several minutes, blot, squeeze; if your hand feels tacky, rinse again | WeAllSew |
| Some body | Soak in warm water; the dissolved solution left in the lace makes it firmer | Sewing machine dealer guide |
| Stiff lace | Wet it without rinsing; the stabilizer is absorbed and dries stiff | Floriani |
| Stiff 3D pieces | Rinse lightly and leave some stabilizer in | OESD |
Dry the lace flat on a thick towel, shaped as it should finish. Hatch blots it between paper towels and presses with a warm iron on a medium setting. If it warps, press it with a pressing cloth; spray starch adds stiffness after the fact. Sulky suggests saving Ultra Solvy offcuts to make a paste for stiffening. Full removal steps are in washaway vs heat-away.
Stabilizer or design: when lace fails
- The stabilizer tears or perforates while stitching
- Support problem: thin film, too few layers, a loose hoop or a burred needle. Change the stabilizer or add a layer.
- The lace falls apart after rinsing
- Design problem. Only designs labeled free-standing or FSL are built to hold together; WeAllSew warns other lace designs "will not hold together properly when the stabilizer is rinsed away." No stabilizer fixes that.
- Outline and fill do not meet
- Usually hooping. Rehoop tighter and check that nothing drags the hoop.
A true FSL file stitches a grid first. In Hatch's example, two identical tatami fills, the second rotated 90 degrees, form the mesh that the satin edges and motifs lock onto. That is why lace is denser than a normal design of the same size; stitch density explains the units if you edit one.
Where this stops applying
- Lace on tulle or organza. That is embroidery on a sheer, not free-standing lace; see the sheers row of the stabilizer chart.
- Designs with stated supplies. The designer's stabilizer and layer count beat every figure here.
- Storage. Washaway reacts to water by design. Sulky packs Ultra Solvy in a reusable clamshell to keep it "fresh and usable for years"; OESD says BadgeMaster and AquaMesh Plus are "not sensitive to air humidity". Keep other brands sealed between projects.
- Products not listed. Layer counts belong to the products named. For another washaway, compare its weight or microns with these before you trust one layer.
Stitch one motif as a test, rinse it and judge the result before you run a set. Change one thing per test, as the Stitch-Out Tuning Method sets out.
Frequently asked questions
Can I use Solvy for free-standing lace?
Not the original thin Solvy on its own: it is a topper and perforates under dense lace. Sulky Ultra Solvy, four times as heavy, is made for lace and takes one layer.
How many layers of water-soluble stabilizer for FSL?
One layer of a heavy lace film such as Ultra Solvy, one layer of Floriani Wet N Gone for most designs, or two layers of Sulky Fabri-Solvy. Add support for very dense designs.
Is fibrous or film stabilizer better for lace?
Either works if the film is a heavy lace grade. Follow the designer's instruction, since some designs are digitized for one type. Fibrous and starch-based types leave more stiffness if not fully rinsed.
How do I make free-standing lace stiff?
Leave some stabilizer in: rinse lightly, or with Floriani Wet N Gone just wet the lace without rinsing so it dries stiff. Spray starch after drying also adds body. See washaway vs heat-away for removal steps.
Why did my lace fall apart when I rinsed it?
The design was not digitized as free-standing lace. FSL designs stitch an underlying grid that holds the lace together once the stabilizer is gone; ordinary lace-look designs do not.
Sources and further reading
- Sulky Answers: Which water soluble stabilizer is best for lace machine embroidery Ultra Solvy 1 layer, Fabri-Solvy 2 layers, follow the designer
- Sulky Answers: Which Solvy is best for stitching free standing lace film type versus fabric type, default of 2 layers of Fabri-Solvy
- Sulky: Ultra Solvy Stabilizer four times as heavy as original Solvy, computerized lace, offcut paste for stiffening
- Sulky: The history of Sulky Solvy uses of Solvy, Super Solvy, Ultra Solvy and Fabri-Solvy
- Madeira USA: Badgemaster 80 micron 80 micron (3.15 mil) heavy weight film, lists free-standing lace
- Madeira UK: Avalon Ultraflat 90 micron 90 micron film for lace digitised for it
- OESD: BadgeMaster WashAway freestanding lace, more starch left behind, paired with AquaMesh, light rinse for stiffness
- OESD: AquaMesh Plus WashAway adhesive mesh, stated uses
- Floriani Wet N Gone (Linda's product page) fibrous, one layer for most FSL, drum tight, wet without rinsing for stiff lace
- WeAllSew: How to make free-standing lace layers, hooping, new 75/11 needle, matching bobbin, rinse test
- Sewing Machine Fun: How to embroider free-standing lace avoid thin topping, smallest hoop, thread, speed, soak versus rinse, starch
- QuiltSocial: 8 essential tips for embroidering free standing lace hoop tighter than fabric, 75/11 sharp, trim and dry
- Hatch Embroidery: Love free standing lace starch-based fibre mesh, matching bobbin, two tatami fills rotated 90 degrees
- ColDesi: Can this be used for free standing lace projects 2 oz tear and wash-away too thick for standalone lace
Found something wrong or out of date? Tell us and we will fix it.