How many stitches does a bobbin last in machine embroidery?
Three figures for bobbin thread per 1,000 stitches circulate, and the lowest one runs bobbins dry. Here is the figure the thread maker publishes, the yardage printed on real bobbins, and the number of stitches that gives.
Quick answer
A prewound L bobbin with about 135 yards (123 m) lasts roughly 35,000 to 41,000 stitches. That is the yardage divided by Madeira's figure of about 3 to 3.5 m of bobbin thread per 1,000 stitches. An M bobbin of 230 yards lasts about 60,000 to 70,000. A self-wound L bobbin holds about half to three quarters as much thread, so plan on roughly 16,000 to 24,000 stitches.
On this page
Key takeaways
- Prewound L bobbin (about 135 yd): roughly 35,000 to 41,000 stitches.
- The rule: stitches = meters on the bobbin ÷ 3 to 3.5 × 1,000. Madeira gives 3 to 3.5 m of bobbin thread per 1,000 stitches.
- Self-wound bobbins hold about half to three quarters of what a prewound of the same thread holds, so they run out much sooner.
- The "one third of the top thread" rule is about the stripe on the back of a satin, not thread length. Used as a length, it doubles your stitches per bobbin on paper.
- Shops report 40,000 to 50,000 stitches from magnetic L bobbins on fill work. Plan with the lower, published figure and you will not run out mid-design.
A prewound L bobbin of about 135 yards lasts roughly 35,000 to 41,000 stitches of normal embroidery. A self-wound L bobbin lasts about half that. Below is the arithmetic, so that you can work out the figure for the exact bobbin in your own machine.
What "stitches per bobbin" means
The bobbin is the small spool under the needle plate that feeds the lower thread. Each stitch locks the top thread around it. Stitches per bobbin is how many stitches one full bobbin sews before it runs out. It depends on two numbers only:
- How much thread is on the bobbin. Makers print this as yards per bobbin. One yard is 0.9144 m.
- How much bobbin thread each stitch uses. This is quoted per 1,000 stitches, because one stitch uses only a few millimeters.
Divide the first by the second and you have the answer. The design's stitch count, shown in your software or on the machine screen, tells you how many of those stitches a job needs.
Bobbins come in standard sizes. L style is common on commercial multi-needle machines. M style is larger and holds more. Class 15 (also sold as 15A or Class 15/A) is common on home machines. A prewound bobbin is wound at the factory and thrown away when empty. Sizes are covered in bobbin thread and prewound bobbins.
How much bobbin thread 1,000 stitches use
Madeira, the thread maker, gives a rule of thumb per 1,000 stitches: top thread "approximately 5 m, bobbin threads approx. 3-3,5 m." The figure is for No. 40 top thread and a 4 mm stitch length. Madeira UK's bobbin page rounds it to about 3 m of underthread and 5 m of top thread.
So bobbin thread runs at about 60 to 70 percent of the top thread, not one third. That is the figure this page uses.
Why the one-third figure is wrong for length
On the back of a balanced satin column you see top thread at both edges and bobbin thread in the middle third. That stripe is the I-test. It is a share of the column's width, seen from underneath, and it says nothing about how many meters each thread uses.
Madeira UK's page states both on one page: the 1/3 bobbin to 2/3 top stripe for correct tension, and about 3 m bobbin against 5 m top per 1,000 stitches. The stripe and the length are different measurements, and our thread usage calculator used to apply the stripe as a length share, so it now starts at 65 percent, Madeira's midpoint.
A third figure circulates too. A SignWarehouse article from 2026 gives about 2 to 2.5 m of bobbin thread per 1,000 stitches, as a rule of thumb, with no source behind it. Many designs do come in there (see the shop reports below), but if you plan on it, some bobbins will run out before the design ends. Plan on Madeira's figure.
Stitches per bobbin, by bobbin
Each row takes the maker's printed yardage, converts it to meters, and divides by Madeira's 3.5 m (low end) and 3 m (high end) per 1,000 stitches. The self-wound rows use Superior Threads' measured ranges for its Bottom Line bobbin thread.
| Bobbin | Thread on it | Stitches, about |
|---|---|---|
| Fil-Tec Magna-Glide Classic, L, white (magnetic, prewound) | 135 yd (123 m) | 35,000 to 41,000 |
| Fil-Tec Magna-Glide Classic, L, black or colors | 130 yd (119 m) | 34,000 to 40,000 |
| Madeira L, paper-sided or magnetic-sided (prewound) | 134 yd (123 m) | 35,000 to 41,000 |
| Fil-Tec Magna-Glide Classic, M, white | 230 yd (210 m) | 60,000 to 70,000 |
| Fil-Tec Clear-Glide, Class 15/A, white (prewound) | 145 yd (133 m) | 38,000 to 44,000 |
| Brother PWB250, size 11.5, 60 wt (prewound) | 105 yd (96 m) | 27,000 to 32,000 |
| Self-wound L, Bottom Line (Superior) | 60 to 80 yd (55 to 73 m) | 16,000 to 24,000 |
| Self-wound M, Bottom Line (Superior) | 120 to 160 yd (110 to 146 m) | 31,000 to 49,000 |
In Fil-Tec's own table the Class 15/A bobbin holds more than its L bobbins of the same thread. Brother's size 11.5 prewound holds less. So do not assume that every home bobbin matches one figure: read the yards per bobbin printed on your own box.
Worked example: a run of left-chest logos
Take a multi-needle machine loaded with a Fil-Tec Magna-Glide Classic L bobbin, white, 135 yards. Suppose the job is 24 left-chest logos of 7,500 stitches each. Walk it through.
- Convert the bobbin to meters. 135 yd × 0.9144 = about 123 m.
- Find the stitches per bobbin. 123 ÷ 3.5 × 1,000 = about 35,000. At 3 m it is about 41,000.
- Find the bobbin thread per logo. 7,500 stitches is 7.5 thousand. 7.5 × 3 to 3.5 m = 22.5 to 26 m per logo.
- Count whole logos per bobbin. 123 ÷ 26 = 4.7, so four logos fit for certain, and a fifth may or may not finish.
- Set the change point. Change the bobbin after every fourth logo. The full run of 180,000 stitches then uses six bobbins, and no logo ever starts on a bobbin that might run dry.
Had you used the one-third rule, you would have budgeted about 12.5 m per logo and expected nine logos per bobbin, and the bobbin would run out partway through the fifth or sixth.
What shops actually get
On The Shirtboard forum, embroiderers asked how many stitches a bobbin lasts. One, using magnetic bobbins, answered "40K to 50K. It all depends on fill types and underlay density." Another said "mid 40,000 on lots of fill or small radials. if big radials less." A third, with magnetic bobbins, sewed two 29,500-stitch badges and part of a third on one bobbin.
Those reports sit at or above the 35,000 to 41,000 worked out from Madeira's figure. On a 135 yd L bobbin, 40,000 to 50,000 stitches works out to about 2.5 to 3 m per 1,000 stitches. So Madeira's figure is the safe planning number, and many real designs will beat it. Designs with heavy underlay or long satins use more thread per stitch and sit at the low end.
Self-wound vs prewound: why the gap is so large
Superior Threads measured the same thread both ways. Its Bottom Line bobbin thread on a self-wound L bobbin held 60 to 80 yards. The prewound version, SuperBOBs, held 118. On M bobbins it was 120 to 160 yards self-wound against 215 prewound. Superior calls it "a major difference between a self-wound bobbin and a professionally-wound prewound bobbin," and adds that self-wound bobbins also differ among themselves with "machine winding tension, speed, and size of thread."
So a self-wound bobbin holds about half to three quarters of a prewound of the same thread. If you wind your own, halve the prewound figure for planning, or count your own as in the bench tip. The trade-offs beyond capacity are in prewound vs self-wound bobbins.
Thread size matters as well as the wind. Tex is the weight in grams of 1,000 m of thread, so a higher Tex is a thicker thread. Fil-Tec's Clear-Spun, a Tex 20 thread, puts 95 yards on a Class 15/A bobbin. Its Tex 12 Clear-Glide puts 145 yards on the same size. If you wind top thread into the bobbin for a two-sided piece, expect far fewer stitches. Weight numbers are explained in thread weights.
If a bobbin runs out mid-design anyway
Many machines warn when the bobbin runs low, but some sensors miss certain prewound styles, covered in bobbin errors. After a change, back the design up a few stitches so the new stitches overlap the old. A new bobbin can also feed with slightly different drag. If bobbin thread starts to show on the front after a change, see bobbin thread showing on top before you touch bobbin tension.
What this does not cover
Madeira's figure is for No. 40 top thread at a 4 mm stitch length. Long satins, thick items such as towels and caps, and a loose bobbin tension all pull more bobbin thread per stitch, so expect fewer stitches. Short fill stitches and light underlay use less, as the shop reports above suggest. The table is arithmetic on printed yardage, not a count anyone ran; the bench tip gives you your own count. The self-wound rows are for Superior's Bottom Line thread on Superior's measurements; your winder may do better or worse. Bobbins not listed here, and colored or specialty bobbin threads, need their own yardage from the box. Fit comes first: a bobbin of the wrong class or height is not a saving at any yardage, so use the size your manual names.
Frequently asked questions
How many stitches does an L bobbin last?
A prewound L bobbin of about 135 yards (123 m) lasts roughly 35,000 to 41,000 stitches, using Madeira's figure of 3 to 3.5 m of bobbin thread per 1,000 stitches. Shops on The Shirtboard report 40,000 to 50,000 on magnetic L bobbins with fill-heavy work. A self-wound L bobbin of 60 to 80 yards lasts about 16,000 to 24,000.
How much bobbin thread does 10,000 stitches use?
About 30 to 35 m at Madeira's 3 to 3.5 m per 1,000 stitches. That is roughly a quarter of a prewound L bobbin. The thread usage calculator does the same sum with a waste allowance.
Is bobbin thread one third of the top thread?
Not in length. One third is the share of a satin column's back that should show bobbin thread in an I-test. By length, Madeira gives about 3 to 3.5 m of bobbin thread against about 5 m of top thread per 1,000 stitches, so 60 to 70 percent.
How many stitches does a Class 15 bobbin last?
It depends on the yardage, which varies by brand. Fil-Tec's Clear-Glide Class 15/A holds 145 yards in white, about 38,000 to 44,000 stitches. Brother's PWB250 size 11.5 prewound holds 105 yards, about 27,000 to 32,000. Read the yards per bobbin on your box and divide its meters by 3 to 3.5.
Why does a prewound bobbin last longer than one I wind myself?
It holds more thread. Superior Threads measured 60 to 80 yards of its Bottom Line thread on a self-wound L bobbin against 118 on its prewound version, because a factory wind is smooth and uniform. See prewound vs self-wound bobbins.
Sources and further reading
- Madeira FAQ: How many stitches can be embroidered with a cone or a spool? Per 1,000 stitches, upper threads approximately 5 m, bobbin threads approx. 3 to 3.5 m; No. 40 thread, 4 mm stitch length
- Madeira UK: Bobbins and underthreads About 3 m underthread and 5 m top thread per 1,000 stitches; 1/3 bobbin to 2/3 top visible underneath for correct tension
- Fil-Tec: Magna-Glide Classic Tex 12; style L 135 yd white, 130 black and colors; style M 230 white, 222 black and colors
- Fil-Tec: Clear-Glide Tex 12; Class 15/A 145 yd white, 135 black and colors; style L 120 and 115
- Fil-Tec: Clear-Spun Tex 20; Class 15/A 95 yd per bobbin
- Madeira USA: Sided Bobbin L (308-503) 134 yards per bobbin, continuous polyester filament, 144 per box
- Madeira USA: Magnetic Bobbin L (308-509) 134 yards per bobbin, magnetic on one side, paper on the other
- Brother USA: PWB250 prewound embroidery bobbins 105 yards of 60 weight polyester per bobbin, size 11.5
- Superior Threads blog: How much thread does my bobbin hold? (June 24, 2009) Self-wound vs prewound capacity for L and M bobbins by thread: Bottom Line L 60 to 80 vs 118 yd, M 120 to 160 vs 215 yd
- The Shirtboard: How many stitches from a bobbin Shop reports: 40K to 50K on magnetic bobbins, mid 40,000 on fills, two 29,500-stitch badges and part of a third
- SignWarehouse: How much thread does an embroidery design use? The circulating 2 to 2.5 m bobbin figure per 1,000 stitches, given without a source
Found something wrong or out of date? Tell us and we will fix it.