How long should a jump stitch be before it is trimmed?
Software defaults say 2 or 3 mm. Brother's jump stitch trim setting starts at 5 mm and goes to 50. Both are right, because they are two different settings at two different stages. Here is what each one controls, every published threshold in one table, and how to make a DST trim where you expect it.
Quick answer
In the design file, trim any connector longer than about 3 mm, and from 2 mm when the thread contrasts with the fabric: shorter jumps are not normally visible (Wilcom), and BERNINA's software default is 2 mm. The machine's own jump trim setting (5 to 50 mm on Brother home machines) only decides which untrimmed jumps it cuts by itself. DST files need the machine's jump count to match the file, usually 3.
On this page
A jump is the hoop moving with the needle out of the fabric, leaving a thread across the gap. Whether that thread gets cut is decided twice: once when the file is written, by the digitizing software's trim threshold, and again at the machine, by its jump trim setting or by how it reads a DST file. Most confusion about the right number comes from mixing up those two stages. For the bigger question of how to avoid jumps in the first place, see stitch order and pathing.
The number to use
In the file: trim connectors longer than 3 mm, or longer than 2 mm when the thread contrasts with the fabric. Wilcom's EmbroideryStudio help puts the line at 3 mm: "Usually, connectors shorter than 3 mm are not visible on the final embroidery," adding that you may need a smaller value "if the thread color contrasts with the background color." BERNINA's V9 software ships with its "Trim if" threshold at 2 mm, and Ignition Drawing, a commercial digitizing service, programs cuts on its standard files "for jumps that are longer than 2mm." Janome's Memory Craft 550E, in its easy setting, trims any jump of 3 mm or longer. Four independent sources land between 2 and 3 mm.
At the machine: set the jump trim length to the shortest jump you would rather not clip by hand. On a Brother home machine the shortest setting is 5 mm. That setting is a second net for files that were written without trims; it does not replace the file's trim commands.
Why not trim everything?
Because every trim costs something, and a jump under 2 to 3 mm costs nothing visible. A trim is not just a cut. The software has to tie off the thread before it and tie in after it: Wilcom notes that "with trims, stitches need to be tied off so the thread can be trimmed without unraveling," and BERNINA's "Always trim" option inserts a tie-in and tie-off between objects "regardless of connector length." Each trim therefore adds lock stitches, a stop for the cutter and a fresh start. Ignition Drawing says plainly that cutting every connection "definitely slows down production time."
On small lettering the cost is worse than time. A trim between every letter leaves short tails that are hard to clip and can pull out the first stitches, which is one of the causes listed under small lettering problems. There, a covered travel run beats a trim at any length.
The opposite mistake is a threshold set so high that long jumps survive. Brother's own help is direct about the trade: the higher the jump length selected, "the fewer number of times the machine will trim, meaning more jump stitches remain on the surface of the fabric." Those are the threads you cut by hand after the hoop comes off, and any you miss stay on the garment.
Every published threshold, side by side
Each figure below is a setting in a specific program or machine. Read the second column before comparing numbers: some count millimeters, some count jump records.
| Source | What it measures | Default or guidance | Range |
|---|---|---|---|
| BERNINA V9 software, "Trim if" | Connector length in the file | 2 mm; tie-ins also start after connectors over 2 mm | User set |
| Wilcom EmbroideryStudio, automatic trim | Connector length in the file | Connectors under 3 mm usually not visible; go smaller for contrasting thread | User set |
| Ignition Drawing, standard file | Jump length in the file | Cuts jumps longer than 2 mm | Also offers cut all or cut none |
| Janome Memory Craft 550E, easy setting | Jump length at the machine | Trims jumps of 3 mm or longer | Advanced setting: trims jumps equal to or longer than the set value |
| Brother home machines, Jump Stitch Trim | Jump length at the machine | Function on from the factory; jumps at or under the setting are not trimmed | 5 to 50 mm in 5 mm steps |
| Brother PR multi-needle, DST jump codes | Consecutive jump records in a DST | 3 | 1 to 8 |
| Janome instruction manual on ManualsLib, jump codes | Consecutive jump records | 3 | 1 to 8; a length option of 1 to 30 mm needs the count set to 8 |
| DST format (EduTech Wiki) | Consecutive jump records | Often 3 | Up to 5 |
Two patterns stand out. Every software or service figure in millimeters sits at 2 or 3 mm. Every machine count for DST defaults to 3. The Brother home range starting at 5 mm is the outlier, and it is the number people quote when they say the threshold is 5 mm: it is the floor of one machine's setting, not a recommendation for the file.
The file setting and the machine setting are different jobs
The digitizing program decides where trim commands go. When a connector is longer than its threshold, it writes a tie-off, a trim and a tie-in into the file. When the file reaches the machine, those trims happen whatever the machine's jump setting says, as long as the machine reads the trim command. Janome's 550E lists this separately as the "cutting command" option: trim "if the imported stitch data file contains a trim command."
The machine's jump trim length acts on jumps that arrive without a trim. Many purchased designs, older files and some auto-digitized files carry plain jumps, and the machine setting is what turns them into cuts. So the order of authority is:
- Set the threshold in your software to 3 mm, or 2 mm for contrasting thread, and let it place tie-offs and tie-ins.
- Route what you can as travel runs under later stitching, so there is nothing to trim. See stitch order and pathing.
- Set the machine's jump trim length for files you did not digitize: the lowest setting gives the cleanest front, and Brother recommends a higher one when a design has many trims, to reduce the tails left on the back.
- Sew a test and look at both sides before running a batch. The Stitch-Out Tuning Method gives the order for any changes after that.
DST files: the trim is a count of jumps
A DST file has no dedicated trim command in its basic form. A trim is signaled by several jump records in a row, and the machine decides how many in a row means "cut here." EduTech Wiki's description of the format puts that number at often 3, but as high as 5. Brother's PR multi-needle machines ship set to 3, adjustable from 1 to 8: three consecutive jump codes become a trim, two are sewn as an ordinary jump.
The rule that follows is Brother's: set the machine's jump number "same as the number that was used when the particular Tajima data was created. If the jump number is not matched, either unexpected trim or no trimming at trim expected point will happen." In Brother's PE-DESIGN, the file side of this is the "Number of jumps for trim" box on DST export. Brother's own example: a file written with 7 jumps per trim on a machine set to 8 does not cut. In Wilcom, the matching control is the trim format, where you enter the number of jumps the machine needs.
A second reason counts go wrong is the length limit on a single record. Wilcom gives the maximum stitch length as 12.1 mm for the ternary coding Tajima machines use (12.7 mm for binary coding, as on Barudan machines), and the format page covered in embroidery file formats notes that longer moves are broken into several jump records. A long move can therefore arrive as a run of jumps, and with a low count setting a machine can read it as a trim. That is one reason not to set the count lower than the file needs.
- Long jump threads where trims should be
- The machine's jump count is higher than the file's, or trims were lost in conversion. Check the export setting against the machine, and see converting file formats.
- Trims in places the design never had them
- The machine's count is lower than the file's, so ordinary multi-record jumps read as trims. Raise the machine count to match the file.
- Stitches unravel next to a trim
- No tie-off before the cut or no tie-in after it. Turn on automatic tie-offs and tie-ins in the software and export again.
Where this stops applying
- Machines with no automatic trimmer. Wilcom warns that such machines "may not know how to interpret Trim functions, and may even shift the design when a trim code is encountered." Its Output Trims checkbox leaves trims out of the file for those machines; you clip by hand.
- Formats other than DST. Brother states that the number of jump codes cannot be set for data other than Tajima (.dst), so the count has no effect on a PES file.
- Open source digitizing. In Ink/Stitch you add trims yourself, with a trim command or the "Trim after" option. Its "minimum jump stitch length" decides whether a gap becomes a jump at all and gets lock and tack stitches; it does not place trims.
- A trimmer that does not cut. Everything here assumes the machine cuts when told to. If trims are in the file and the knife still leaves the thread whole, see thread trimmer not cutting.
- Your exact machine. The ranges above are for the machines named. Look for "jump stitch trim", "jump thread cutting" or "DST jump codes" in your manual, and set it during first-time setup.
If you are weighing how many trims a design can afford, the stitch time calculator counts each trim as run time, and single vs multi-needle machines covers why trims cost more on some machines than others.
Frequently asked questions
What length jump stitch should be trimmed?
Trim connectors longer than about 3 mm in the file, and longer than 2 mm when the thread contrasts with the fabric. Wilcom says connectors under 3 mm are usually not visible; BERNINA's software default is 2 mm. Shorter jumps are better left or replaced with a covered travel run.
What should I set Brother's jump stitch trim to?
The setting runs from 5 to 50 mm in 5 mm steps, and jumps at or below the setting are not trimmed. Use the low end for a clean front; Brother recommends a higher setting when a design has many trims, to reduce tails on the back. Trims already in the file happen either way.
Why does my DST file not trim on my machine?
DST signals a trim as several jumps in a row, and the machine must be set to the same count the file was written with, usually 3 (Brother PR machines accept 1 to 8). A machine set higher than the file ignores the trims. See converting file formats if the file was converted.
Do jump stitches need tie-off stitches?
Before a trim, yes: the thread must be tied off so it can be cut without unraveling, and the next object needs a tie-in. Wilcom places tie-offs before trims and uses tie-ins when the previous connector is trimmed; BERNINA's "Always trim" adds both. Untrimmed short jumps do not need them.
Sources and further reading
- Wilcom EmbroideryStudio help: Automatic trim settings Connectors under 3 mm usually not visible; smaller value for contrasting thread
- Wilcom EmbroideryStudio help: Trim functions Jumps-as-trims format; Output Trims; machines without trimmers may shift the design
- Wilcom EmbroideryStudio help: Stitch and jump length settings Maximum stitch 12.1 mm ternary (Tajima), 12.7 mm binary (Barudan)
- Wilcom EmbroideryStudio help: Types of connectors Tie-offs placed before trims; tie-ins when the previous connector is trimmed
- Wilcom EmbroideryStudio help: Use jumps as connectors Trim off, always, or only above a set length; trims need tie-offs
- BERNINA V9 software help: Connector settings Trim if default 2 mm; Always trim adds tie-in and tie-off; tie-in default 2 mm
- Brother: Using the thread trimming function (Jump Stitch Trim) On from the factory; 5 to 50 mm in 5 mm steps; higher setting for designs with many trims
- Brother PR1050X FAQ: Specifying jumpstitch trimming or DST jump codes for trimming DST jump count 1 to 8, default 3; match the count used to create the file
- Brother PE-DESIGN FAQ: DST export and jump stitch cutting on PR machines Number of jumps for trim on export; 7 in the file and 8 on the machine does not cut
- Janome Memory Craft 550E instruction book Easy setting trims jumps of 3 mm or longer; jump thread cutting length; cutting command
- Janome instruction manual on ManualsLib, page 65 Jump code threshold default 3, 1 to 8; length threshold 1 to 30 mm with the count at 8
- EduTech Wiki: Embroidery format DST Trim assumed after a run of jumps, often 3, up to 5
- Ignition Drawing: What to do with connection threads Standard files cut jumps longer than 2 mm; cutting all slows production
- Ink/Stitch: Tack and lock stitches Trim after and trim commands; minimum jump stitch length decides jump vs stitch
Found something wrong or out of date? Tell us and we will fix it.