Why is my embroidery machine not cutting the thread at trims?

Press Trim with the needle plate off and watch the knife. Whether it stays still, moves without cutting, frays the thread or cuts so short the needle unthreads points to a different part, and only one of the four is a worn knife.

Updated 8 min read Reviewed against our editorial standards

Quick answer

Press Trim with the needle plate off. If the knife does not move, check the thread cutting setting is on, then clear thread jamming it and check the drive rod. If it moves but does not cut, clean out packed lint, then inspect the fixed knife and under thread presser. Frayed ends mean too much presser pressure. A needle that unthreads at the next start means the tail is too short.

On this page
  1. Which symptom do you have?
  2. The blade does not move
  3. The blade moves but does not cut
  4. It cuts, but the ends fray
  5. The thread pulls out at the next start
  6. Home single-needle vs commercial trimmers
  7. When to call a technician

Watch the knife while you press the trim key: what it does tells you which of four faults you have. If the blade does not move, the trim command is not reaching it or something is jamming it. If it moves but the thread survives, thread is packed against the knife or the knife edges no longer meet. If it cuts but leaves frayed ends, the thread is being crushed rather than sheared. And if it cuts cleanly but the needle comes unthreaded at the next start, the trimmer is fine and the tail is the problem. A new knife, the fix most people reach for, answers only one of those four.

Which symptom do you have?

Take the needle plate off (on a commercial head, the sewing arm covers too) so you can see the blade, then press Trim with the machine idle. Ricoma's own procedure starts exactly here: expose the blades, clear any thread build-up, press the key and see whether they move.

Trimmer not cutting: symptom, likely cause and first fix
What you seeMost likely causeNext most likelyFirst fix
Stops at the end of a color without cuttingThread cutting setting offNo trim in the fileTurn the setting on; check the file
Blade does not move, or "Trim not in position"Thread or a nest jamming the knifeDrive rod or link disconnectedClear the knife area, press Trim to reset
Blade moves, thread not cutLint and thread packed at the knifeWorn or misaligned fixed knife; crumpled under thread presserClean, then inspect the knives
Cuts, but the ends frayUnder thread presser pressing too hardWorn knifeTest and replace the presser
Thread pulls out of the needle at the next startTail length too shortPicker or upper thread catcher not holdingLengthen the tail one step, test the picker
Long tails left on the workTail or length after trim too longThread wound too often round the break sensorShorten the tail one step

The blade does not move

The trim is turned off, not broken

Confirm the machine was asked to cut. Brother home embroidery machines have two settings. End Color Trim cuts at the end of each color and is on from the factory; with it off, "the machine will stop without cutting the thread". It also returns to its default when the machine is switched off, so a machine that skipped trims all afternoon and cuts normally the next morning had the setting changed, not a fault. Jump Stitch Trim, also on by default, keeps its setting after power-off, and its 5 to 50 mm length decides which jumps get cut: the higher the number, Brother says, the fewer times the machine trims.

If trims are missing in one design only, the file is the fault. In a DST file a trim is a run of jumps the machine reads as a cut when the count matches its own setting; that mismatch is covered in jump stitch trim length.

Thread is jamming the knife

Ricoma explains its "Trim not in Position" message as the knife being unable to return to its home position, "usually due to a buildup of excess thread under the needle plate or bird nesting". Take the plate off, pull out the thread and press the trim key to reset the knife. On Ricoma's CHT and CHS heads the same fault shows as error 257; if clearing thread does not clear it, the black arm beside the cylindrical sensor under the machine, toward the back on the right, has to be turned back into line with the sensor until its light comes on. If a nest caused the jam, fix that too, or the next trim jams the same way: see bird nesting.

The drive is disconnected

With the knife area clean and the blade still not moving, Ricoma's next check is whether the rod is connected to the blades, and on its MT and TC machines whether the bar on the back of the sewing arm is in place. Beyond that is technician work. If the panel shows a code rather than plain words, reading error messages explains how to decode it.

The blade moves but does not cut

Lint and thread at the knife

Fix this first on every machine. Brother's answer for PR600 to PR1000E owners whose knife does not cut every time is to remove the needle plate and "clean out any loose thread from around the hook area" before going to a service center. On Brother home machines, a dirty area under the needle plate is on the same short list as a bent needle and wrong upper threading. Amaya UK's Melco guide says to clean the trimmer and rotary hook area and lubricate when refitting. The routine is in cleaning the bobbin area; look at the knives while it is open.

Worn or misaligned fixed knife

A commercial trimmer is a moveable knife that swings across a fixed knife. Melco's tech manual names "wear or misalignment of the adjustable fixed knife" as a cause of poor trimming or none at all. To check it, read the marks on the moveable knife where the fixed knife contacts it, or run an ink wipe-off test; the cure is adjustment, replacement or both. Ricoma says the blade should sit with "only the tip visible" and publishes a separate adjustment video per model, so use your maker's procedure rather than bending parts by eye.

Crumpled under thread presser

The part most people never look at is the under thread presser, which holds the bobbin thread under the moveable knife after the cut so there is a loop for the next stitch. Melco says that once it is "crumpled" by contact with the moveable knife it can prevent cutting. The test below tells you whether to replace it.

It cuts, but the ends fray

A frayed cut is a crushed cut. Melco says the under thread presser should press only hard enough to retain the thread beneath the moveable knife, and that excessive pressure "prevents loop formation or frays threads". These faults can mimic tension problems, which is how a trimmer fault ends up chased with the tension knobs. Melco's check:

  1. Switch the machine off and disconnect the connecting link from the moveable knife drive arm at the front pin.
  2. Pull the moveable knife forward with a small Allen wrench.
  3. Drape bobbin thread over it and push it back. The cut should be clean, not frayed.
  4. Check what stays. The top thread should fall away while the bottom thread stays held.
  5. If it fails, replace the presser, repeat the test, then reattach the link.

Thread matters too. Melco's AMAYA has a Trim Type setting to switch to metallic for metallic thread. On home machines, The Sewing Studio notes thick, metallic and invisible threads "can be too tough for the built-in blade", and Brother says to cut special decorative threads with the side cutter.

The thread pulls out at the next start

A clean trim followed by an unthreaded needle means the knife did its job. Bill Garvin of BG Tech Services, an embroidery machine repair company, explains that the picker works with the trimmer and the upper thread catcher to manage tail length and help the machine start. When it misbehaves, the top thread "isn't connecting with the bobbin on startup or after a trim", and the sensor may report a thread break, so the fault gets filed under thread breaking.

Check the setting first. Melco's AMAYA offers short, medium or long tails, medium by default; other machines use a number, and Garvin cites seven to 17, higher meaning longer. His rule settles it: too long creates extra trimming work, too short causes pull-outs. Move one step and test. Then the hardware: push the picker in by hand and it should spring back on its own; pressing Trim tests it electrically, and Ricoma machines have a Pick Test. Pickers most often get bent catching on bulky garments as they come off, Garvin says, and can usually be bent back by hand. The upper thread catcher, Velcro bar included, can fail in ways that look like a picker fault.

Long tails are the same setting the other way. Ricoma's fixes: see whether one needle or all do it, clear the thread path, run an I-test, adjust the Velcro bar and spring lever, test the picker, reduce "Length After Trim", turn "Trim Start Angle" down, and check timing. It also lists thread wrapped too many times round the thread break sensor, which lets the machine move off before the tails are pulled through.

Home single-needle vs commercial trimmers

A home single-needle machine has one cutter the owner cleans but does not adjust: Brother's list stops at needle, threading and lint, then sends you to a service center. A commercial head has a moveable knife, an adjustable fixed knife, an under thread presser, a picker and a thread catcher, plus tail and trim angle settings on the panel, and the makers publish owner checks for most of them. The wider differences are in commercial embroidery machines.

When to call a technician

Stop when the knife will not move with a clean knife area and every link attached, when it moves but will not cut after cleaning and a new fixed knife, or when the fault points at trim timing, which Ricoma lists as a cause of tails. When to service covers what to tell the technician. Short of that, work the table from the top and stitch a short test after each change, as in the stitch-out tuning method.

Frequently asked questions

Why does my embroidery machine stop at the end of a color without cutting?

On Brother home machines the most likely reason is that End Color Trim is turned off. With it off the machine stops without cutting. It returns to its default (on) when the machine is switched off, so a restart often clears it. If only one design does it, check the file's trims; see jump stitch trim length.

What does "Trim not in position" mean?

On Ricoma machines it means the trimming knife cannot return to its home position, usually because thread has built up under the needle plate or a bird nest has formed. Remove the plate, clear the thread and press the trim key to reset the knife.

Why does the thread come out of the needle after a trim?

The tail left after the cut is too short, or the picker and upper thread catcher are not holding the thread for the next start. Lengthen the tail setting one step, then push the picker in by hand: it should spring back on its own. A bent picker can usually be bent back by hand.

Should I replace the trimmer knife if it stops cutting?

Only after cleaning. Packed lint and thread, a disconnected drive rod, a setting turned off and a crumpled under thread presser all stop the cut with a good knife. Melco names wear or misalignment of the fixed knife as a cause, checked by the contact marks on the moveable knife.

Sources and further reading

Found something wrong or out of date? Tell us and we will fix it.