What is the minimum stitch length in machine embroidery?
One camp says 1 mm. Software filters say 0.1, 0.3 or 0.8 mm. They are answering different questions: how short a stitch you should digitize, and how short a stitch is junk to delete. Here are both numbers, every published figure in one table, and why the needle sets the limit.
Quick answer
Digitize no stitch shorter than about 1 mm with a standard 75/11 needle: Melco's guidance is run stitches 1.5 mm or longer, satin 1 mm, fill 2 mm, because a stitch should be longer than the needle is thick (0.75 mm on a 75/11). The 0.1 to 1.0 mm values in small stitch filters only delete leftover tiny stitches; they do not make a design safe.
On this page
Every stitch is a needle hole and the thread between two holes. Make the gap shorter than the needle is thick and the next penetration lands in or against the last one, through thread that is already there. That is the whole reason a minimum exists, and it is why the number moves with the needle.
The numbers to use
Keep every stitch you digitize at 1 mm or longer, and longer still for runs and fills. Melco's thread break troubleshooting guide for its DesignShop software gives the clearest published set of minimums. Its general rule is "to keep stitch lengths longer than the diameter of the needle you are using," and because "most needles are between 7 and 8 points in diameter," it says to keep stitches 10 points long or longer. Melco measures in points, and one point is a tenth of a millimeter, so 10 points is 1 mm. The same guide calls these "good general minimums":
| Stitch type | Melco minimum | In mm | What it applies to |
|---|---|---|---|
| Walk (run) stitch | 15 points or more | 1.5 mm | Outlines, detail lines, underlay and travel runs |
| Satin | 10 points or more | 1.0 mm | The stitch across the column, so this is also the narrowest column width |
| Fill | 20 points or more | 2.0 mm | Stitches within each row of a tatami or similar fill |
| Any stitch, general rule | 10 points or more | 1.0 mm | Longer than the needle blade is thick |
Melco adds that the values "may be altered if the application or design dictates." They are minimums, not targets: ordinary runs sit around 1.5 to 3 mm and fill stitches around 3 to 4 mm, as the stitch types table shows.
Why the needle sets the limit
The size number on a needle is its thickness. SCHMETZ explains that the metric size "indicates the diameter of the needle blade in hundredths of a millimeter," so an NM 80 needle has a blade 0.80 mm across. A 75/11 is 0.75 mm, a 65/9 is 0.65 mm and a 90/14 is 0.90 mm. Melco's 1 mm general minimum is simply a round number just above the 0.7 to 0.8 mm of the needles most embroidery runs on.
Two things follow. A finer needle allows a slightly shorter stitch, which is part of why 60 wt thread on a 65/9 or 70/10 needle can sew smaller lettering, as covered in embroidery lettering. A heavier needle needs longer stitches. Wilcom's EmbroideryStudio help says the same from the other direction: "generally the minimum stitch length is increased for dense materials and thick threads to prevent thread breakage." If you move up to a 90/14 for 30 wt thread, do not keep the 1 mm figure; see embroidery needles for which needle goes with which thread.
When the rule is broken, the damage shows up as a thread fault. Melco ties stitches below needle size to thread breaks on "thin outlines or small elements or lettering," and Wilcom's help says "small stitches can damage fabric and cause thread or needle breakage." That is why thread breaking that repeats at the same detail on every garment points at the file before the machine.
Small stitch filters: a cleanup setting, not the minimum
Most digitizing programs have a filter that deletes stitches below a length you choose. Its defaults are far lower than 1 mm, and that is where the competing numbers come from. They are not wrong; they answer a different question.
| Program | Setting | Default or guidance | Exceptions |
|---|---|---|---|
| Ink/Stitch | Minimum stitch length (global, overridable per object) | 0.1 mm; owners of W6 machines should set at least 0.3 mm or stitches may go missing | Lock stitches are never dropped |
| Melco DesignShop | Built-in filtering | Removes every other stitch below 5 points (0.5 mm) | Melco says this alleviates the problem "but it may not solve it completely" |
| mySewnet digitizing | Minimum Significant Stitch Length (Stitch Length Optimizer) | 0.8 mm; choices are 0.6, 0.8 or 1.0 mm | Cutwork needle lines are not affected |
| Wilcom EmbroideryStudio | Remove Small Stitches; Minimum Stitch in machine format settings | User set; raise it for dense materials and thick threads | Can run always, on output only, or never |
| Hatch Embroidery | Remove Small Stitches | User set | Same always or on output choice as Wilcom |
A filter deletes a stitch and joins its neighbors; it does not lengthen anything. That makes it the right tool for the debris a design collects, such as near-zero stitches where two objects meet, points doubled by editing, or the shortened stitches a stitch file gets when it is shrunk without being regenerated. It is the wrong tool for a satin column that is 0.6 mm wide all the way along: a filter set high enough to catch that would remove the column.
So use two numbers, at two stages. Design to the Melco minimums above. Then leave a cleanup filter on output at 0.5 to 0.8 mm, the range DesignShop and mySewnet use by default. Ink/Stitch's 0.1 mm default only clears out what is effectively a zero-length stitch, which is why it suggests 0.3 mm for W6 machines.
What a near-zero stitch actually does
A DST file records each move in units of 0.1 mm, so the shortest stitch a file can hold is 0.1 mm, and a stitch of 0 is the needle going down into the same hole. A Brother patent on embroidery data processing describes what happens when lock stitch data is written as moves of "0 to 0.05 mm": several stitch positions are "concentrated substantially at the same location," the seam swells, the thread "is susceptible to being cut due to damage by the needle by later stitching," and loops remain on the underside "since a thread tightening operation cannot be carried out sufficiently." The patented fix spreads those stitches apart, changing the move from 0 to 0.3 mm.
That covers three common faults at once: thread cut at a detail, a hard knot on the face and loops on the back. Very short stitches also cause skipped stitches and thread shredding.
How to fix short stitches in a design
Work in the object file if you have one: a stitch file can only be filtered, an object file can be rebuilt. The order runs from the least to the most visible change.
- Find them. Use the ruler or stitch list on the thinnest satins, the tightest curves and the smallest letters. Melco's threshold for action is a satin stitch "less than ten points or one millimeter wide."
- Turn off short stitch shortening on narrow columns. The short stitch feature alternates stitch lengths on the inside of curves to stop build-up, but Melco notes it "can cause stitches that are too small in smaller lettering or narrow satin stitches." Since DesignShop V9 it switches itself off for stitch lines under 20 points (2 mm); check the setting in files saved in older versions.
- Widen the column. Pull offset adds length to both ends of each satin stitch. Melco's example takes a 5 point satin, adds 3 points each side and gets an 11 point column. A minimum column width of 10 points stops any satin or fill stitch line coming out shorter than 1 mm. See pull compensation for how much is too much.
- Use fewer points on runs. Melco's advice for thread breaks on walk stitches is to avoid lengths under 15 points and to "use fewer points to create the same shape." On a curve, shorten the stitch only as far as the curve needs: Wilcom's own example for sharp curves is 1.8 mm, still above the run minimum.
- Change the stitch type or the size. A column that cannot reach 1 mm is a run, not a satin. Lettering too small to keep its satins at 1 mm needs a larger size, a finer needle and thread, or a font built for small text; the checks are in small lettering problems.
- Filter last, then sew a test. Run the small stitch filter on output, export, and stitch the problem area on the real fabric. The Stitch-Out Tuning Method gives the order for any change after that.
Where these numbers stop applying
- Lock stitches. Tie-ins and tie-offs are short on purpose, often about 1 mm or less, and Ink/Stitch exempts them from its filter. Keep them out of the same holes rather than lengthening them, and see stitch order and pathing for where they belong.
- Your machine. Ink/Stitch's W6 note shows that some machines misbehave on very short stitches. If a machine drops stitches the file clearly contains, raise the filter value and check your manual.
- Heavy needles and threads. The figures are for the 7 to 8 point needles Melco names. On a 90/14 or larger, raise the minimum.
Short jumps are a separate setting: Ink/Stitch's default minimum jump stitch length is 3 mm, and which jumps get trimmed is covered in jump stitch trim length.
Frequently asked questions
What is the shortest stitch an embroidery machine can sew?
Formats such as DST store moves in 0.1 mm steps, so a file can hold a 0.1 mm stitch, and a 0 mm stitch lands in the same hole. Sewing them is another matter: a stitch shorter than the needle is thick (0.75 mm on a 75/11) pierces thread already there, so keep designed stitches at 1 mm or longer.
What should I set Remove Small Stitches to?
Use it as cleanup on output at about 0.5 to 0.8 mm, the range Melco DesignShop and mySewnet apply by default. Do not raise it to fix narrow satins or short runs: a filter deletes stitches, it does not lengthen them. Widen or reroute those objects instead.
What is the minimum satin stitch width?
About 1 mm with a 75/11 needle and 40 wt thread, because each satin stitch is the width of the column. Melco treats satins under 10 points (1 mm) as a thread break risk. Below that, use a run, or a finer needle and 60 wt thread for small lettering; see embroidery lettering.
Is a 0.3 mm minimum stitch length safe?
As a filter value it is reasonable: Ink/Stitch recommends at least 0.3 mm for W6 machines, and a Brother patent spreads stacked lock stitches to 0.3 mm. As a design length it is far too short. Visible stitches should stay at 1 mm or more, runs at 1.5 mm and fills at 2 mm.
Sources and further reading
- Melco service: Stitches Too Small Keep stitches longer than the needle diameter; run 15, satin 10, fill 20 points; DesignShop filtering below 5 points; short stitches off under 20 points; pull offset and minimum column width
- SCHMETZ: Needle size designations NM size is the blade diameter in hundredths of a millimeter
- Wilcom EmbroideryStudio help: Eliminating small stitches Small stitches can damage fabric and break thread or needles; filter always or on output
- Wilcom EmbroideryStudio help: Stitch and jump length settings Minimum Stitch sets the small stitch default; increase it for dense materials and thick threads
- Wilcom EmbroideryStudio help: Stitch length settings 1.8 mm run on sharp curves; variable run length with a minimum length
- Hatch Embroidery: How to remove small stitches in Hatch 3 Remove Small Stitches, user-set minimum, always or on output
- mySewnet help: Stitch Length Optimizer options Minimum significant stitch length 0.6, 0.8 or 1.0 mm, default 0.8 mm; cutwork lines unaffected
- Ink/Stitch: Preferences Minimum stitch length drops shorter stitches except lock stitches; at least 0.3 mm for W6 machines
- Ink/Stitch source: default settings Default minimum stitch length 0.1 mm, minimum jump stitch length 3 mm
- Brother Industries patent US6298276B1: Embroidery data processing apparatus Stitches of 0 to 0.05 mm concentrate at one spot, swell the seam, cut thread and leave loops; spread to 0.3 mm
- EduTech Wiki: Embroidery format DST DST coordinates in 0.1 mm units; 121 unit maximum stitch
Found something wrong or out of date? Tell us and we will fix it.