Can you keep an embroidery machine in a cold garage?

The operating range from five makers in one table, the one storage range any of them publish, and why damp air and fast warming do more harm than the cold itself.

Updated 7 min read Reviewed against our editorial standards

Quick answer

You can store one there if the garage stays dry, but do not sew in it below the maker's range. Brother rates the PR650e for 41 to 95°F (5 to 35°C) at 20 to 80 percent humidity; Ricoma rates its Creator for 40 to 104°F (5 to 40°C); Melco's Bravo needs 59°F (15°C). Bernina says to put a machine stored in the cold in a warm room for one hour before use.

On this page
  1. Key takeaways
  2. Temperature and humidity ranges by maker
  3. Is it the cold or the damp?
  4. What cold does to a machine
  5. Worked example: a PR650e in a winter garage
  6. How to keep a machine in a garage
  7. What this does not cover

Key takeaways

  • Sew only inside the maker's operating range. Brother PR650e: 41 to 95°F (5 to 35°C), 20 to 80 percent humidity. Ricoma Creator: 40 to 104°F (5 to 40°C).
  • Some machines need more warmth. Melco's Bravo is rated from 59°F (15°C), so a garage that suits a Brother can be too cold for it.
  • Storing the machine there is a separate question. Damp air and fast swings in temperature are what makers warn about, because they cause condensation and rust.
  • Bring a cold machine into a warm room one hour before you sew, as Bernina's manual says. Keep it away from space heaters.
  • Keep the thread indoors even if the machine stays out. Rayon is the most sensitive to cold, damp and swings.

Yes, you can keep an embroidery machine in a cold garage, as long as the garage is dry and you warm the machine before you sew. What you should not do is run it in the cold. Brother rates the PR650e to run at 41 to 95°F (5 to 35°C), with 20 to 80 percent humidity. Ricoma rates its Creator for 40 to 104°F (5 to 40°C). Below about 41°F, both machines are outside the conditions their makers say they will work in.

Two terms carry the rest of this page. The operating range is the band of room temperature and humidity a maker says the machine may be switched on and sewing in. The storage range is the band it may sit in, switched off. Storage ranges are wider, and most makers do not publish one at all. Relative humidity is how much water the air holds, as a percentage of the most it could hold at that temperature. At 100 percent, water starts to form as droplets on any surface colder than the air. That is condensation, the same wet film that forms on a cold drink on a summer day.

Temperature and humidity ranges by maker

These are the figures each maker prints in its own manual or spec sheet. Each one is for the model named, not for the brand as a whole.

Embroidery machine temperature and humidity ratings, as each maker states them
MachineOperating temperatureHumidityStorage or cold-weather note
Brother PR650e (6-needle)41 to 95°F (5 to 35°C)20 to 80 percentNo storage figure on the spec sheet
Ricoma Creator40 to 104°F (5 to 40°C)None givenKeep out of direct sunlight; no storage figure
Melco Bravo59 to 104°F (15 to 40°C)85 percent at mostIndoor use only; no storage figure
Tajima TMAR-KC and TMAR-VC41 to 104°F (5 to 40°C)30 to 95 percent, without condensationStorage 14 to 140°F (-10 to 60°C)
Bernina 735No figureDry rooms onlyIf stored in a cold room, put it in a warm room one hour before use
Brother home machines (SE700 manual)No figureAvoid high humidityDo not store where it is extremely cold, or where the temperature changes sharply

Two things stand out. First, the low end is about 41°F (5°C) on every machine that gives a number, except the Melco Bravo, which wants 59°F (15°C). Second, Tajima is the only maker here that prints a storage range, and it goes down to 14°F (-10°C). The machine switched off can take far more cold than the machine sewing. Ricoma's 40°F and its own 5°C are not quite the same number (5°C is 41°F). Read it as "about 40°F" and do not sew at the edge.

The humidity limits vary more. The PR650e runs at 20 to 80 percent, Melco's Bravo at up to 85 percent, and Tajima's heads at 30 to 95 percent, but only without condensation. Melco marks the Bravo for indoor use only. Bernina gives no number and says to use its machine only in dry rooms. Ricoma's manual gives no humidity figure.

Is it the cold or the damp?

Two answers circulate. One says cold does not hurt a machine that is switched off. The other says never keep one in a garage. The makers' own wording settles it: the cold is a limit on sewing, and the damp is the risk in storage.

Read Brother's storage list in its home machine manuals. It says not to store the machine where it is "exposed to extremely low temperatures", "exposed to extreme temperature changes" or "exposed to high humidity or steam". It names the damage too: "rust caused by condensation." Tajima writes the same limit into its spec as humidity "without condensation". Neither maker sets a number for how cold is too cold in storage, but both name water on the machine as the harm.

So the question for a garage is not just how cold it gets. It is whether the machine gets wet. A dry garage that stays cold is a mild place to store one. A garage that is damp, or swings from freezing at night to warm in the afternoon sun, is the one to avoid. Each warm, moist spell after a cold night is a chance for water to form on cold metal.

What cold does to a machine

Stiff oil

Oil gets thicker as it cools. Union Special, a maker of industrial sewing machines, describes the effect in a patent for a system that heats the oil before sewing starts. Until the oil warms, it says, "power consumption is greater and lubricant flow characteristics throughout the system are slowed." Warming the oil first, it says, cuts power use and the time the machine takes to reach speed.

Bernina's 735 manual lists the same kind of symptom without naming the cause. Its troubleshooting table gives "unfavorable room temperature" as a reason for speed too low and for the machine doesn't start. The fix in both rows is the same: put the machine in a warm room one hour before use. Do not add oil to free a cold machine. More oil is still cold oil, and oiling covers why extra oil only collects lint. If a machine that has warmed up still stalls, read motor lock and main shaft errors.

Condensation on the electronics

Condensation is the reason the hour matters. A machine that sat in a cold garage is cold all the way through. Carry it into a warm, humid kitchen and the room air meets cold metal, a cold screen and cold circuit boards. Water can form on all of them before the machine catches up with the room.

Brother says this in plain words in its troubleshooting table. If the LCD screen is fogged up, "condensation has formed on the LCD screen," and "after a while, the cloudiness will disappear." The fog you can see on the screen tells you water may be forming on parts you cannot see. Brother's storage warning puts rust from condensation in the same list. Tajima's humidity limit, "without condensation", rules out running the machine with water on it at all. Wait it out with the power off.

Thread, and rayon most of all

The thread is more fragile than the machine. Ricoma's Creator manual calls rayon "susceptible to damage by environmental factors, such as light, heat and cold". Madeira says rayon fibers "become weaker while wet". Ricoma's thread guide puts storage at 65 to 75°F (18 to 24°C) and around 50 percent humidity, and warns against spaces with "big temperature swings that can weaken your threads over time." A cold garage is one of those spaces. Weak thread breaks at speed, and that looks like a machine fault when it is not; see thread breaking.

So if the machine lives in the garage, the thread should not. Thread shelf life and storage gives the range every thread source agrees on, and how to test a spool that has been left out. Polyester vs rayon thread covers why polyester copes better.

Worked example: a PR650e in a winter garage

Take a Brother PR650e kept in a detached garage. Suppose the garage drops to 35°F (2°C) on a winter night, and you want to sew a run of shirts there in the morning. Walk it through the figures.

  1. Check the room against the range. 35°F is below the PR650e's 41°F floor. As the room stands, the machine is outside the conditions Brother rates it for. Do not switch it on to see if it runs.
  2. Choose: heat the garage or move the machine. A 6-needle machine is not easy to carry, so heating the garage may be the practical choice. A single-needle machine is simpler to bring indoors.
  3. Heat the room, not the machine. Brother's home manuals say not to use or store the machine "near a space heater". Put the heater across the garage, not aimed at the machine. Fast, local heat is the extreme temperature change Brother warns about.
  4. Read the humidity. A cheap hygrometer on the wall answers this. The PR650e is rated for 20 to 80 percent. If the reading is over 80, or you see fog on the screen or wet metal, wait.
  5. Give the machine its hour. Start the clock once the room itself is warm, not when you switch the heater on. One hour is Bernina's figure for a machine stored in the cold. Brother publishes no warm-up time, so Bernina's hour is the only maker figure to go on.
  6. Stitch a test before the real job. Bring the thread out from the house. Run a short test design at a moderate speed, as in first-time setup, and listen for a heavier sound than usual. Then load the shirts.

Swap in a Melco Bravo and the answer changes at step 1. Its floor is 59°F (15°C), so the garage has to get much warmer before it is in range. The same heater that brings a PR650e garage to 45°F leaves a Bravo out of spec.

How to keep a machine in a garage

  1. Find your model's range. Look in the specifications or the safety pages of the manual. If it gives no number, as on Brother home machines, follow its storage list: no extreme cold, no sharp changes, no damp.
  2. Keep it dry. Cover the machine. Bernina recommends storing its machines in the original packaging.
  3. Keep it out of the sun and away from heaters. Ricoma's manual says to keep the machine out of direct sunlight. Brother lists a flame, heater or air conditioner among places not to store it.
  4. Warm it slowly before every session. Room first, then one hour for the machine with the power off.
  5. Keep the thread in the house. Bring out only what the session needs.
  6. Run it now and then. Brother's Luminaire manual says to turn the machine on and use it periodically, because long storage without use "may reduce its efficiency". Before a long gap, clean it as in cleaning the bobbin area.

What this does not cover

These are the published figures for six named machines, and they stop there. Your model may differ, even from the same maker, so check its own manual before you trust a number from this page. Tajima's storage range is the only one any maker here prints, and it is for a commercial head. It does not tell you how cold a home machine can be stored, and no source here gives that figure. Nothing here covers a machine that has been wet or frozen with water inside it. If a machine shows rust, will not start once warm, or sounds rough after storage, take it to a technician; when to service lists the signs. Electrical safety in a garage, such as the outlet, extension cords and a damp floor, is outside this page and outside these manuals' ranges. What the machine draws, and whether the garage circuit can carry it, is in how many watts an embroidery machine uses.

Frequently asked questions

What temperature is too cold to use an embroidery machine?

Below the bottom of the maker's operating range. That is 41°F (5°C) for the Brother PR650e and Tajima's TMAR heads, about 40°F (5°C) for the Ricoma Creator, and 59°F (15°C) for the Melco Bravo. Check your own model's manual.

How long should a cold embroidery machine warm up before sewing?

One hour in a warm room, with the power off. That is Bernina's instruction for a machine stored in a cold room, and the only warm-up time a maker publishes among these sources. Start counting once the room is warm.

Can an embroidery machine freeze in storage?

Tajima rates its TMAR heads for storage down to 14°F (-10°C). No home machine maker here gives a storage figure: Brother only says to avoid extremely low temperatures, sharp changes and high humidity, because of rust from condensation.

Why is my embroidery machine screen foggy?

Condensation. Brother says the cloudiness on the LCD goes away after a while. It usually means a cold machine has been brought into warmer, moist air. Leave it switched off until the fog has cleared and the machine has had its hour.

Can I store embroidery thread in the garage?

Better not. Ricoma calls rayon susceptible to light, heat and cold, and warns against spaces with big temperature swings. See thread shelf life and storage for the conditions thread makers give.

Sources and further reading

Found something wrong or out of date? Tell us and we will fix it.