How many watts does an embroidery machine use?

Maker ratings for home, single-head and multi-head machines in one table, the circuit check for a long run, and the electricity cost of one shirt worked through.

Updated 7 min read Reviewed against our editorial standards

Quick answer

About 90 watts for a home machine (bernette b79) and 160 to 480 watts for a single-head multi-needle (Tajima TMBR2-SC 160 W, Melco EMT16X 480 W). Melco's head draws 4 amps at 120 volts, so one head runs on an ordinary 15-amp outlet circuit without a dedicated line. Check what else shares the breaker.

On this page
  1. Key takeaways
  2. Watts, amps and volts in plain words
  3. Embroidery machine power by maker
  4. Do you need a dedicated circuit?
  5. Worked example: one Melco head on a 15 A circuit
  6. Home vs multi-needle: what changes
  7. What this does not cover

Key takeaways

  • A home embroidery machine uses about 90 watts. That is the bernette b79's rating, less than an old 100-watt light bulb.
  • A single-head multi-needle machine is rated at 160 to 480 watts. Melco's EMT16X and Bravo X draw 4 amps at 120 volts.
  • One head does not need a dedicated circuit. 4 amps fits a 15-amp household circuit with room to spare, even on a job that runs for hours.
  • Electricity is a small cost. Even at Melco's full 480 watts, one 16-minute logo works out to about 2 cents at the August 2026 US average price.
  • Count everything else on the same breaker. A heater or a heat press on that circuit is what trips it, not the machine.

A home embroidery machine uses about 90 watts, and a single-head multi-needle machine 160 to 480 watts. The bernette b79, a home sewing and embroidery machine, is rated at 90 W. Tajima rates its TMBR2-SC single head at 160 W. Melco rates its 16-needle EMT16X at 480 W, which it gives as 4 amps at 120 volts. None of these needs a dedicated circuit. One head on an ordinary 15-amp outlet circuit uses about a quarter of what that circuit can carry.

Watts, amps and volts in plain words

Three units carry this page, so here they are first.

A watt (W) is the rate at which a machine uses electricity. A bigger number means more power drawn at any moment. A volt (V) is the push of the supply: about 120 V from a normal US wall outlet, 230 V in much of Europe. An amp (A) is how much current flows through the wire. Multiply volts by amps and you get roughly the watts. That is why Melco can write the same machine as "4A at 120V AC and 2A at 240V AC (480 Watts)". Double the volts and the amps halve for the same power.

Your breaker cares about amps. Your electric bill cares about kilowatt-hours (kWh). One kWh is 1,000 watts used for one hour, or 100 watts for ten hours.

Two more terms come up. A VA (volt-ampere) figure is the volts times the amps the wiring actually carries. For machines with motors and power supplies it can be higher than the watts, which is why Tajima prints both. A dedicated circuit is a circuit with its own breaker that feeds one appliance and nothing else.

Embroidery machine power by maker

These are the figures each maker prints for the model named. They are ratings, not meter readings.

Embroidery machine power ratings, as each maker states them
MachineTypeRated powerSupplyCurrent
bernette b79Home sewing and embroidery, single needle90 W100 to 240 VNot stated
Tajima TMBR2-SCSingle head, 6 to 18 needles160 WSingle phase, 100 V or 200 VNot stated
Melco EMT16XSingle head, 16 needles480 W90 to 260 V, single phase4 A
Melco Bravo XSingle head, 16 needles480 W90 to 260 V, single phase4 A at 120 V, 2 A at 240 V
Tajima TMAR-KCMulti-head, 2 to 8 headsMaximum 470 W (910 VA)3-phase 200 V, or single phase 100 V or 200 VNot stated
Brother PR1055XHome multi-needle, 10 needlesNo figure in the manual"Regular household electricity"Not stated

The home machine is the easy case. At 90 W, the bernette b79 uses less than an old 100-watt light bulb. Brother's PR1055X manual gives no watts at all. It calls the machine "intended for household use" and says to use "only regular household electricity". That is the same outlet you would plug a lamp into.

The single heads sit higher. Melco's two 16-needle heads are the only machines here with an amp figure. The EMT16X manual lists "90-260V (Single Phase, 50/60 HZ, 4A)" and 480 W. The Bravo X manual splits it out: 4 A at 120 V and 2 A at 240 V. Tajima's TMBR2-SC page gives 160 W on a single-phase 100 V or 200 V supply.

The multi-head row needs care. Tajima's TMAR-KC brochure covers machines from 2 to 8 heads. It prints one line for the whole series: "Maximum 470W (910VA)". It does not say which head count that figure belongs to. So do not divide it by the heads, and do not read it as "an 8-head uses less than one Melco". Makers rate power in different ways, and only the same maker's figures compare cleanly.

Want the amps for a machine that gives only watts? Divide watts by your volts. 90 W at 120 V is about 0.75 A. That is our arithmetic, not a bernette figure, and it ignores the gap between watts and VA. For Tajima's VA figure, the same sum gives about 4.6 A at 200 V or 9.1 A at 100 V. Tajima states neither.

Do you need a dedicated circuit?

Two answers circulate. One says a multi-needle machine needs its own circuit, or even 240 V. The other says it plugs into any outlet. For one head, the makers' own figures settle it: any normal outlet circuit will do, as long as you check what else is on it.

Start with the amps. Melco's single head draws 4 A at 120 V. A typical household outlet circuit has a 15-amp or 20-amp breaker; the number is on the breaker handle. 4 A is about a quarter of 15 A.

Long jobs are the next check. The US electrical code calls a continuous load one where "the maximum current is expected to continue for 3 hours or more". A breaker for a continuous load must be rated at no less than 125 percent of that load. Thomas Domitrovich explains the result in IAEI Magazine: it puts the breaker at 80 percent of its rating. On a 15 A breaker, that is 12 A for anything that runs three hours or more. A 4 A head fits inside 12 A three times over.

So where does the other answer come from? Partly from multi-head machines. Tajima offers the TMAR-KC with a 3-phase 200 V supply, which no house outlet provides. That is a real wiring job, but it is not what a single head asks for. Melco's EMT16X and Bravo X run on 90 to 260 V single phase. The TMBR2-SC single head is single phase only.

What makers do ask for is a clean connection. Brother says to plug the PR1055X straight into the wall: "Do not use extension cords or multi-plug adapters with many other appliances plugged in to them." Melco recommends a line conditioner, a box that evens out the supply, for up to four machines at a time. It does not recommend running several machines from "simple power strips".

A dedicated circuit makes sense when the circuit is already busy. The loads to look for are heaters, kettles, irons and a heat press for patches. Add the amps on their rating plates to the machine's 4 A. If the total passes 12 A on a long run, move one of them or add a circuit. A shop running several heads is in the same position. Four Melco heads at 4 A each come to 16 A. That is more than one 15 A circuit should carry for hours.

Worked example: one Melco head on a 15 A circuit

Take a Melco EMT16X on a 120 V outlet with a 15 A breaker. Suppose you run a batch of left-chest logos for four hours. Walk it through the published figures. The sums below are our arithmetic.

  1. Find the machine's draw. Melco's manual gives 4 A at 120 V, or 480 W.
  2. Decide whether it is continuous. Four hours is over the code's three-hour line, so treat it as a continuous load.
  3. Check the breaker. 4 A times 125 percent is 5 A. The 15 A breaker is well above that. Put the other way, 80 percent of 15 A is 12 A, which leaves 8 A for anything else on the circuit.
  4. Check the rest of the circuit. Turn off the breaker and see what goes dark. Add the amps from the rating plate of anything else that will run during the batch. Keep the total, machine included, at 12 A or less.
  5. Work out the energy. 480 W for four hours is 1.92 kWh. That is the most it can be, because 480 W is the rated figure, not the average while stitching.
  6. Price it. The US average residential price in August 2026 was 18.16 cents per kWh, from the EIA. 1.92 kWh times 18.16 cents is about 35 cents for the whole four hours.

Now per shirt. A 10,000-stitch logo at 800 stitches per minute takes about 15 to 16 minutes of stitching, as the stitch time calculator shows. At 480 W, 16 minutes is 0.128 kWh, or about 2.3 cents. Swap in the bernette b79 at 90 W and an hour of stitching is 0.09 kWh, under 2 cents. Use the price on your own bill; it may be far from the average.

Home vs multi-needle: what changes

The jump from a home machine to a single head is about five times in rated power, from 90 W to 480 W. In daily use, that difference shows up in amps on the breaker, not on the bill. The real choice between them is about needles, caps and finished garments, covered in single vs multi-needle and how to choose a machine.

Where the power question does change is at the next step up. A multi-head frame, or several single heads side by side, adds up quickly. That is the point to read the manual's supply page, ask about 3-phase options, and talk to an electrician before the machine arrives. Commercial machines explains how single, multi-head and linked setups differ, and commercial brands covers who makes them.

What this does not cover

These are maker ratings for six named machines. No maker here publishes what its machine draws on average while stitching. So every cost above is an upper limit, and your model may differ from the one named. Ricoma is left out because no rating for its machines could be found, and Brother's PR1055X manual gives none. The circuit figures are for US 120 V circuits and the US electrical code; other countries use other voltages and rules. This page does not tell you how your house is wired. If a breaker trips with only the machine running, or an outlet feels warm, stop and call an electrician. The machine's own faults are in when to service. Machines kept in a garage or shed have their own limits, set out in embroidery machine in a cold garage. Setting the machine up once it is plugged in is in first-time setup.

Frequently asked questions

How many amps does an embroidery machine draw?

Melco's EMT16X and Bravo X single heads draw 4 A at 120 V and 2 A at 240 V. A 90 W home machine such as the bernette b79 works out to under 1 A at 120 V; that is our arithmetic, since bernette gives only watts.

Does a multi-needle embroidery machine need a 20 amp circuit?

Not for one head. A 4 A head fits within the 12 A a 15 A breaker should carry for a job of three hours or more. A 20 A circuit helps only if other loads, such as a heater or heat press, share it.

Can I plug an embroidery machine into a power strip?

Brother says to plug the PR1055X straight into the wall, with no extension cords or multi-plug adapters loaded with other appliances. Melco does not recommend simple power strips for several machines and suggests a line conditioner instead.

How much does it cost to run an embroidery machine?

Very little. At Melco's full 480 W and the August 2026 US average of 18.16 cents per kWh, a 16-minute logo costs about 2.3 cents. A 90 W home machine costs under 2 cents an hour. Your own price per kWh is on your bill.

Does a commercial embroidery machine need 240 volts or 3-phase?

Single heads do not. Melco's EMT16X runs on 90 to 260 V single phase, and Tajima's TMBR2-SC on single phase. Tajima offers its TMAR-KC multi-head with 3-phase 200 V or single phase. Read the supply line for your model before it arrives.

Sources and further reading

Found something wrong or out of date? Tell us and we will fix it.