How wide should the satin stitch be on appliqué?
3 to 4 mm when you trim with scissors in the hoop, 2 to 2.5 mm only when the piece is cut to shape before it goes down. The cover is centered on the tack-down line, so only half its width hides the cut edge.
Quick answer
Set the cover satin to 3 to 4 mm for appliqué trimmed with scissors in the hoop: Bernina's class handout uses 3.5 mm and a Brother tutorial 4.0 mm. A 2 mm border works only for pre-cut or machine-cut pieces. The satin sits centered on the tack-down, so a 2 mm border reaches just 1 mm past it. Keep spacing near 0.4 mm and stay under about 6 mm.
On this page
Make the cover satin 3 to 4 mm wide if you trim the appliqué fabric with scissors in the hoop, and 2 to 2.5 mm only when the piece is cut to shape before it goes down. mySewnet starts a satin border at 2 mm, and that is too narrow for an edge trimmed by hand. The cover stitch sits centered on the tack-down line, so only half its width reaches out over the strip of fabric your scissors left. Below are the widths software and maker tutorials actually use, the geometry that decides between them, and the order to fix a fuzzy edge in. For the full appliqué sequence of placement, tack-down and cover, see the appliqué section of the projects guide.
Widths software and tutorials use
No maker publishes a single correct width. What they publish are defaults and worked examples, and those cluster in two places: about 2 mm as a starting value, and 3.5 to 4 mm when someone is teaching a hand-trimmed appliqué.
| Source | Cover width | Context |
|---|---|---|
| mySewnet (Husqvarna Viking, Pfaff) satin border | 2.0 mm default, settable 1 to 12 mm | No edge-walk underlay below 2 mm; appliqué piece margin defaults to 1.0 mm |
| mySewnet sketch satin lines | Presets of 2, 4 and 6 mm | The 2 mm line has no underlay; 4 and 6 mm do |
| BERNINA 9 class handout, appliqué patch | 3.5 mm | Tack and cover offsets moved 0.25 mm so "the cover will cover the raw edge of the cut applique piece" |
| BERNINA 9 class handout, letter with holes | 2.5 mm | Paired with the CutWork tool, so the piece is machine cut |
| BERNINA 9 class handout, converted design | Tack-down zigzag 1.5 mm | BERNINA help: tack-down width "cannot be greater than cover stitch width" |
| Brother My Design Center tutorial (EmbroideryHoop notes) | 4.0 mm | "2.0mm is too narrow for beginners trimming with scissors"; density raised to 110% |
| A digitizer on the DigitSmith forum | From about 2 mm to 3.2, moving to 3.5 mm | Also uses a denser satin |
Read the two clusters as two jobs. A 2 to 2.5 mm border is the right width for a piece whose edge lands on the tack-down line, which is what a cutting machine or a pre-cut shape gives you. A 3.5 to 4 mm border is what teachers set when the reader will trim by hand.
The half-width rule
The satin straddles the tack-down. BERNINA's help gives the satin cover offset a default of 0, and Wilcom's EmbroideryStudio help measures cover offset from the tack stitch: negative moves the border in, positive moves it out. At zero offset, half the satin lies over the appliqué fabric and half lies outside the tack-down, over whatever your scissors left.
So the useful number is half the width. A 2 mm satin covers 1 mm outside the tack-down, 3 mm covers 1.5 mm, 4 mm covers 2 mm. Now set that against how much fabric hand trimming leaves. EmbroideryHoop's notes on a multi-appliqué lesson aim to leave "about 1mm - 2mm of fabric outside the tack-down line", and put the tack-down "roughly 1.5mm to 2mm inside the final satin edge." For a centered satin, that inset is exactly a 3 to 4 mm border. A 2 mm border has no margin at all: its outer needle penetrations fall on the raw edge, and the fibers they disturb stand up through the stitches. Quilt Social's tester saw that fringe on a Husqvarna Viking appliqué and put it down to two causes: fabric not trimmed close enough, or a satin not "quite as wide as it can be to hide that raw edge."
Pull matters too. A satin column draws in as it stitches, which is why pull compensation exists, and a border that stitches narrower than it was digitized loses width on both sides, including the outer half that covers the edge.
Which width for which job
| Job | Start at | Why |
|---|---|---|
| Pre-cut or machine-cut pieces placed on the line | 2 to 2.5 mm satin, or a zigzag or E-stitch | The edge sits on the tack-down, so there is no strip to cover |
| Cotton or other woven trimmed in the hoop | 3.5 to 4 mm | Covers up to about 2 mm of leftover fabric |
| Patches with a satin border | 3.5 mm or more, with underlay | BERNINA's patch example; the border also has to hold the cut patch edge |
| Children's wear where a soft edge matters | E-stitch instead of satin | Ink/Stitch describes it as a "deceivingly strong" cover for baby clothes |
| Bold decorative borders | Up to about 6 mm | Past 6 mm, one digitizer on DigitSmith switches to a satin fill |
The upper end is a satin limit, not an appliqué one. Several digitizers in a DigitSmith thread keep ordinary satins at 6 mm or less, one moving to a satin fill past 6 mm. Wilcom suggests staying within 10 mm and calls 15 mm a high snagging risk; mySewnet's lettering help gives 10 mm as the maximum before stitches lie loose. The stitch types guide covers the E-stitch, whose prongs cross the edge only at intervals, so it needs the closest trim of all.
Spacing, underlay and offset
Width is one of three settings that decide whether the edge disappears. Change them in this order of preference.
- Offset before width. BERNINA's handout moves both tack and cover 0.25 mm outward instead of widening the border. A small outward offset puts more of the satin over the cut edge without making the border look heavier.
- Spacing near 0.4 mm. The site's density converter gives about 0.4 to 0.5 mm for an appliqué cover satin. On DigitSmith, one digitizer calls 0.38 "plenty" and warns that if you have to widen the border to cover, "something is not right." The Brother tutorial raised density to 110% because fabric color peeked through on curves. Tighter spacing hides show-through and some fuzz from a fraying fabric, but it cannot reach an edge that lies outside the border; more in stitch density.
- Underlay at 2 mm and up. mySewnet adds no edge-walk underlay below 2 mm. Its 2 mm satin line has none, while the 4 and 6 mm lines do. Give a 3 to 4 mm border an edge walk; see underlay.
Keep the tack-down inside the cover. A zigzag or E-stitch tack-down that is wider than the satin shows on both sides of it, which is why BERNINA will not let the tack-down exceed the cover width.
Fix a fuzzy edge in this order
- Trim closer. Kimberbell's advice for a satin-covered piece is to trim close to the stitch line so the border "completely covers the edge." Take the hoop off the machine without unhooping and use curved or duckbill appliqué scissors.
- Check the tack-down caught the fabric all round. If the piece shifted, base fabric shows between appliqué and satin; Make ma!'s troubleshooting table blames shifting and uneven trimming, and for fibers past the satin, heavy fraying or loose trimming. A light mist of spray, as in adhesives and fusibles, holds the piece.
- Move the cover outward. Try a 0.25 mm positive offset first.
- Widen to 3.5 to 4 mm. Only if trimming and offset are not enough.
- Clean up what remains. Quilt Social's tester trimmed the leftover fuzz with small sharp scissors after removing the stabilizer.
Change one setting per test stitch-out, as the Stitch-Out Tuning Method sets out, or you will not know which one worked.
- Threads or fibers standing up along the outside of the satin
- Edge too far out for the half-width. Trim closer, then offset, then widen.
- A gap of base fabric between the appliqué and the satin
- The piece crept before or during tack-down. EmbroideryHoop's notes fix it with spray adhesive or a magnetic hoop for better grip, not a wider border.
- Appliqué color showing through the satin on curves
- Spacing too open, not width. Tighten spacing slightly.
- A narrow border puckers or tunnels
- Satin pulling the fabric; see satin stitch problems.
Where this stops applying
- Raw-edge appliqué. No satin at all: Kimberbell leaves a sliver about 1/8 in wide showing and trims about 1/8 in from the stitch line on purpose.
- Bought stitch files. Widening a border in a stitch file only stretches existing stitches. Change width in the object file, or in a program that recalculates; see stitch vs object files. A file that runs straight through with no stop for trimming lost its stops in conversion.
- Tackle twill letters. Bought cut letters are heat tacked on their line, so they take 2 to 4 mm by letter height at an open zigzag; see tackle twill stitch width.
- Small lettering. Counters and serifs leave no room for a 4 mm border. Cut those pieces to shape and use 2 to 2.5 mm, as BERNINA does for its letter.
Frequently asked questions
What width satin stitch for appliqué?
3 to 4 mm when you trim the fabric with scissors in the hoop; BERNINA's class handout uses 3.5 mm and a Brother tutorial 4.0 mm. Use 2 to 2.5 mm only for pre-cut or machine-cut pieces. Stay under about 6 mm for an ordinary border.
Why does fabric fray out from under my appliqué satin?
The satin is centered on the tack-down, so only half its width covers fabric left outside it. A 2 mm border reaches 1 mm out. Trim closer, move the cover 0.25 mm outward, and widen to 3.5 to 4 mm only if that is not enough.
What density should an appliqué satin border be?
Around 0.4 mm spacing, 0.4 to 0.5 mm on the density converter. Tighten it slightly if the appliqué color shows through on curves; it will not hide a raw edge outside the border.
Should the tack-down be narrower than the satin?
Yes. A zigzag or E-stitch tack-down wider than the cover shows on both sides of it. BERNINA's software does not allow a tack-down wider than the cover stitch.
Sources and further reading
- mySewnet help: Satin Border satin border 1 to 12 mm, 2.0 mm default, no underlay below 2 mm
- mySewnet help: Appliqué appliqué methods and piece margin, 1.0 mm default
- mySewnet help: Satin Line 2, 4 and 6 mm presets, underlay on 4 and 6 mm only
- mySewnet help: Large Lettering 10 mm maximum satin length in a column
- BERNINA of America: Simply Applique (BERNINA 9 class handout) 3.5 mm patch cover, 2.5 mm letter, 1.5 mm tack-down, 0.25 mm offsets
- BERNINA help: Adjust appliqué stitch settings satin offset default 0, blanket -1.50, tack-down no wider than cover
- Wilcom EmbroideryStudio help: Adjust cover stitch settings cover offset measured from the tack stitch
- Wilcom: Mastering basic stitch types satin within 10 mm, 15 mm high snagging risk
- EmbroideryHoop: digitizing an appliqué in My Design Center, part 2 4.0 mm cover and 110% density for scissor trimming
- EmbroideryHoop: multi-appliqué digitizing, placement, tack-down and trim tack-down 1.5 to 2 mm inside the satin edge, trim 1 to 2 mm outside it
- DigitSmith forum: Applique tricks and tips cover widths of 2 to 3.5 mm, 0.38 spacing
- DigitSmith forum: What is the widest you will digitize a satin stitch digitizers' practical satin limits around 6 mm
- Ink/Stitch: E-stitch E-stitch as an appliqué cover for baby clothes
- Kimberbell: All about applique, tips and tricks trim close under satin, 1/8 in for raw-edge appliqué
- Quilt Social: trimming machine embroidery appliqué fuzz from loose trimming or a narrow satin
- Make ma!: Machine embroidery appliqué, step by step appliqué troubleshooting table
Found something wrong or out of date? Tell us and we will fix it.