What zigzag or satin width should tackle twill letters be sewn with?
2 mm for letters 1 to 3 in tall, 3 mm for 4 to 9 in, 4 mm for 10 in and up, at 15 stitches per inch. In embroidery software that is an open zigzag of about 3.4 mm peak to peak, nowhere near a cover satin.
Quick answer
Use Stahls' figures: a 2 mm zigzag for letters 1 to 3 in tall, 3 mm for 4 to 9 in, 4 mm for 10 in and up, at 15 stitches per inch (about 1.7 mm per needle drop, 3.4 mm peak to peak). Heat tack the twill first at 330°F (165°C) for 8 to 10 seconds. Zigzag for jerseys, satin to hide the edge.
On this page
Sew tackle twill letters with a 2 mm zigzag for letters 1 to 3 in tall, 3 mm for 4 to 9 in, and 4 mm for 10 in and up, all at 15 stitches per inch. Those are Stahls' figures for its Poly-TWILL, and they are narrower than the 3.5 to 4 mm cover satin appliqué guides recommend for a good reason: a cut twill letter is pressed down exactly where it will be sewn, so there is no trimmed strip to bury. Below: the widths, what 15 stitches per inch means in embroidery software, which stitch to pick, and the heat tack that keeps the letter still.
Width by letter height
Stahls' Poly-TWILL sewing sheet ties stitch width to the height of the letter, number or logo, and recommends "a tight, zig-zag stitch or satin stitch". The last three columns are the site's arithmetic, not Stahls' figures.
| Letter height | Stitch width | Stitches per inch | Reach onto the twill (half width) | Needle drops per 10 in of edge | Same edge as a 0.4 mm satin |
|---|---|---|---|---|---|
| 1 to 3 in | 2 mm | 15 | 1 mm | 150 | about 1,270 |
| 4 to 9 in | 3 mm | 15 | 1.5 mm | 150 | about 1,270 |
| 10 in and up | 4 mm | 15 | 2 mm | 150 | about 1,270 |
Width scales with the letter; stitch count does not. The sheet also says to "increase number of stitches per inch for larger letters, to reduce sewing time", which contradicts both itself (more stitches per inch means more sewing) and the table printed below it. Follow the table.
Letters under 1 in are not covered; for text that small, stitch it and use the minimum sizes in embroidery lettering.
15 stitches per inch in digitizing terms
Stahls wrote its sheet for a household zigzag sewing machine (its tension diagram is headed "thread tension using a household sewing machine"), so its stitches per inch is a sewing machine figure. A sewing machine counts every needle drop as one stitch, and each drop alternates between the left and right side of the zigzag. So:
- Between consecutive needle drops: 25.4 mm divided by 15 is about 1.7 mm of travel per stitch.
- Peak to peak: two drops make one full zig and zag, so the same side of the column repeats every 3.4 mm, about 7.5 times per inch.
Which one goes in the spacing field depends on the software. Ink/Stitch defines satin spacing as "the peak-to-peak distance between zig-zags", so there the figure is about 3.4 mm. Wilcom's cover stitch help only says to adjust spacing on the Fill tab for "more or less dense cover stitching" and does not say which distance it measures. The check that works in any program: stitch or simulate one straight inch of the border and count the needle drops. Fifteen is Stahls' density; 30 or 8 means the software measured the other distance.
That is the reason Ignition Drawing calls the zigzag "a very open column" while Stahls calls it "tight". Both describe the same stitch. Stahls is comparing it with looser zigzags on the same sewing machine; Ignition is comparing it with an embroidery satin. A cover satin at 0.4 mm peak-to-peak spacing puts about 127 needle drops in an inch, eight and a half times as many. Stitches per square inch works the same conversion for fills and satins of every width.
Zigzag, satin or run stitch
Ignition Drawing, a digitizing service, lists the three stitches used to attach twill and what each leaves you with.
| Stitch | Edge of the twill | Use it for | Starting setting |
|---|---|---|---|
| Zigzag | Runs over the edge; edge "slightly visible but still held down" | Sports jerseys: Ignition calls it "a durable stitch" | Stahls width by height, 15 needle drops per inch |
| Satin | Solid; "will completely cover the edge" for a finished look | Fashion wear, mascots, any piece where no twill edge should show | Same widths, ordinary cover satin spacing |
| Run stitch | Left loose; the line sits 1 to 2 mm inside the edge | A raw, worn edge on purpose | Single run 1 to 2 mm in from the cut edge |
Stahls states that Poly-TWILL "must be sewn to prevent fraying", and a run stitch leaves the outer 1 to 2 mm unsewn. Choose it when a frayed edge is the point, never to save stitches on a uniform.
A satin cover on twill uses the Stahls widths, not the appliqué widths, for the same reason the zigzag does: the edge already sits on the line. Its spacing is the ordinary satin spacing of about 0.4 mm that the density converter gives for a cover satin; stitch density explains the trade-off. The stitch types guide covers how satin and run stitches behave in general.
Why twill can go narrower than appliqué
The site's appliqué satin border width guide recommends 3.5 to 4 mm for appliqué trimmed with scissors in the hoop, and warns that a 2 mm border leaves fuzz. Stahls recommends 2 mm for small twill letters. Both are right.
- Where the edge is. Scissor trimming leaves 1 to 2 mm of fabric outside the tack-down, and a satin centered on the tack-down covers only half its width past that line. A 4 mm satin reaches 2 mm out and buries the strip. A cut twill letter has no strip: the cut edge is the line, so a 2 mm zigzag already reaches 1 mm onto the twill and 1 mm onto the garment.
- What the border must hide. The appliqué satin has to hide a ragged scissor cut. The twill border only holds a pre-cut edge, and Stahls says its Plasti-Bak adhesive coating gives "easy handling and smooth, clean sewing".
- Density. The appliqué cover is a solid satin of about 127 drops per inch. A twill zigzag is 15, because on a jersey the twill is meant to show and the stitch only has to stop the edge lifting.
So the appliqué page's 2 to 2.5 mm for pre-cut pieces and Stahls' 2 mm for small letters are the same rule. Twill you trim in the hoop yourself is ordinary appliqué again, and takes the 3.5 to 4 mm satin.
Tack the twill before you sew
A 2 mm border bites only 1 mm on each side, so a letter that creeps 1 mm escapes it. Stahls fixes the letter with heat before any stitching.
- Pre-press the garment to remove wrinkles and moisture.
- Put a pillow inside the garment so the press does not mark it around the letters.
- Lay the letters in place.
- Press at 330°F (165°C) for 8 to 10 seconds at medium pressure (#4 on a Hotronix press). For a dry run, Stahls notes that tacking for only 2 to 3 seconds still lets you realign a letter that has shifted.
- Two or three color letters: tack the foreground layer to the background between two cover sheets, sew those two together first, then tack the finished letter to the garment for the final sewing.
Those settings are for the twill's own adhesive coating, not for pressing a finished patch with heat seal film; that has its own settings in heat press settings for patches.
In software, a heat-tacked letter does not need a stitched tack-down. Wilcom's appliqué help lets you choose a run, zigzag or E-stitch tack, or "select None" to omit tacking entirely; that is the setting for a letter the press has already fixed. Keep a placement line so you know where the letter goes. Uncoated twill has no adhesive to press, so it needs either a light spray (see adhesives and fusibles) or a stitched tack-down kept narrower than the cover.
Setting it up in software
- Cover type and width. Wilcom lets you change the cover stitch to zigzag, E-stitch or raised satin. Pick zigzag or satin, and the width from the table by finished letter height.
- Offset zero. Wilcom measures cover offset from the tack stitch: a negative value moves the border in, a positive one out. Centered on a cut edge, half the width falls on each side, which is what the half-width column assumes.
- Spacing. For the zigzag, set it so one inch holds 15 needle drops (about 3.4 mm peak to peak); for satin, about 0.4 mm.
- Close the letter. Stahls sews 4 to 8 stitches past the starting point "for improved durability"; in a file, overlap the border's start by a few stitches.
- Test one letter on the job's fabric and backing, changing one setting at a time, as the Stitch-Out Tuning Method sets out.
If the border misses the edge on one side, the letter moved: tack longer at the press rather than widening the border to chase it.
Where this stops applying
- Other twill brands. The widths and the press settings are Stahls' for its Poly-TWILL, dated 2012. Another maker's coated twill may need a different temperature or time; use its sheet for the press, and keep the widths as a starting point.
- Needle, thread and speed. Stahls gives none; set them as for any embroidery on the same garment, and if a satin border puckers the garment, look at pull compensation and satin stitch problems.
Frequently asked questions
What stitch width for tackle twill letters?
Stahls gives 2 mm for letters 1 to 3 in tall, 3 mm for 4 to 9 in and 4 mm for 10 in and up, all at 15 stitches per inch. Use the same widths for a zigzag or a satin cover.
What is 15 stitches per inch in embroidery spacing?
About 1.7 mm between needle drops, or about 3.4 mm peak to peak, the way Ink/Stitch measures satin spacing. Count one inch of the stitched border: it should hold 15 needle drops.
Zigzag or satin for tackle twill?
Zigzag for sports jerseys: it is open, durable and lets the twill edge show. Satin when the edge should be completely covered. A run stitch 1 to 2 mm inside the edge leaves it loose, so use it only for a worn look.
Why is tackle twill sewn narrower than appliqué?
Cut twill letters are heat tacked exactly on their line, so there is no trimmed strip to cover. Scissor-trimmed appliqué needs 3.5 to 4 mm; see appliqué satin border width.
What heat press setting tacks twill letters?
Stahls tacks Poly-TWILL at 330°F (165°C) for 8 to 10 seconds at medium pressure, after pre-pressing the garment, with a pillow inside it.
Sources and further reading
- Stahls: How to sew Poly-TWILL (technical sheet) 2, 3 and 4 mm widths by letter height at 15 stitches per inch; 330°F (165°C), 8 to 10 s, medium press tack; two-color layering
- Ignition Drawing: Tackle twill, a guide zigzag, satin and run stitch compared; run stitch 1 to 2 mm inside the edge
- Ignition Drawing: Tackle twill, go big with less stitches zigzag, run or satin to sew the twill down
- Wilcom EmbroideryStudio help: Adjust cover stitch settings cover type zigzag, E-stitch or raised satin; width, offset and spacing
- Wilcom EmbroideryStudio help: Adjust tack stitch settings run, zigzag or E-stitch tack, or None
- Ink/Stitch: Satin column zig-zag spacing is the peak-to-peak distance between zig-zags
Found something wrong or out of date? Tell us and we will fix it.