What should bobbin tension be on a gauge for machine embroidery?

Two figures circulate for the same gauge: 18 to 22 grams and 180 to 220 grams. Only one of them can be grams. Here are the readings thread and machine makers publish, gathered in one table, and how to take a reading you can trust.

Updated 7 min read Reviewed against our editorial standards

Quick answer

On a TOWA-type bobbin case gauge reading in grams-force, set a metal embroidery bobbin case to 18 to 22 g for flat goods (Madeira's figure) or 22 to 25 g (the TOWA digital guideline), and up to 25 g for caps. The "180 to 220 grams" figure is the same setting read on a dial that counts in tens. On a Melco, use Melco's own gauge and its 250 to 300 reading.

On this page
  1. The number to set
  2. 18 to 22 grams or 180 to 220 grams?
  3. What each maker publishes
  4. How to take a reading you can trust
  5. Set the bobbin first or the top first?
  6. Caps and heavy goods
  7. Melco and home machines: different gauges, different numbers
  8. When these numbers stop applying

The number to set

Set a metal embroidery bobbin case to 18 to 25 grams of pull on a TOWA-type gauge, at the low end for flat goods and up to 25 g for caps. Madeira's tension guide gives "18 to 22 grams (up to 25 grams when embroidering caps)". The guideline Madeira prints for the TOWA digital gauge sits a little higher: 22 to 24 gf for everyday embroidery and 25 gf for caps on its UK shop, 22 to 25 gf on its US product page. If you have no other figure to go on, start at 22 g: it is inside both ranges.

Those numbers are for the push-in metal cases of multi-needle machines on a pulley-type case gauge. They do not transfer to a drop-in home machine or to a different gauge. If you are still deciding whether the bobbin needs touching at all, read how to check and adjust bobbin tension first.

18 to 22 grams or 180 to 220 grams?

The TOWA analog case gauge text, as AllBrands publishes it for the L, M and class 15 models, says: "Correct bobbin tensions should be 180 to 220 grams (up to 250 grams when embroidering caps)." The next sentence says: "If your gauge is shown in units of 10's, the correct bobbin tensions should be 18 to 22 grams (up to 25 grams when embroidering caps.)" Both describe one setting; most pages quote only the first.

The 18 to 22 g reading is the one in grams. Three checks settle it:

  • It matches every gram-force figure. Madeira's guide says 18 to 22 grams, the TOWA digital gauge (which displays gf) 22 to 25 gf, and the Tajima TTG 200-10 gauge 20 to 35 for polyester bobbin thread.
  • 180 g would outpull the top thread. The same makers set top thread at 100 to 150 grams (Madeira's guide: rayon 100 to 120, polyester 120 to 150). A bobbin pulling 180 to 220 g would be stronger than the top thread, the reverse of the balance every one of these sources describes.
  • The ratio holds. On both Madeira's and the TOWA digital figures, top thread runs about five to seven times the bobbin. 180 g of bobbin would need a top thread of about a kilogram.

So 180 to 220 is a dial number. Divide by ten and it is the same advice.

What each maker publishes

Every published embroidery reading we found, with the gauge it belongs to. Read across a row: a number only means something on its own gauge.

Published bobbin and top thread tension readings for machine embroidery, by source and gauge
SourceGaugeBobbin, flat goodsBobbin, capsTop thread
Madeira USA tension guideNot named; grams18 to 22 gUp to 25 gRayon 100 to 120 g; polyester 120 to 150 g
TOWA analog case gauges (AllBrands product text)TOWA L, M and class 15 dials, 0 to 400 g180 to 220, or 18 to 22 g read in tensUp to 250, or 25 gNot given
Madeira UK, TOWA digital gaugeTOWA digital, set to gf22 to 24 gf25 gfRayon 150; Polyneon 170; Frosted Matt 170; metallic 180 gf
Madeira USA, TOWA digital gaugeTOWA digital, L insert22 to 25 gfNot split outRayon 40: 150; Polyneon 40: 170; metallic 40 to 50: 170; Polyester CR 40: 125; Burmilana 12: 190 gf
Tajima TTG 200-10 (AllBrands)Tajima pull gauge, 0 to 250 g20 to 35 (polyester 120/2 bobbin thread)Not givenRayon 100 to 130; polyester 110 to 150
Madeira, Tajima gauge instructionsTajima pull gaugeNot givenNot givenClassic Rayon 40: 120 to 130; Polyneon 40: 140 to 150; #60: 100 to 110; Polyneon 75: 95 to 100 g
Melco support (Amaya UK)Melco gauge PN 34746 or digital PN 35583250 to 300 (no unit given)Not split outNot given
Echidna (home machines)Echidna push-pull gauge, thread tied to the hook30 to 50 g for most machines; 75 g tightNot applicableNot given

Top thread figures for the TOWA digital gauge (150 to 190 gf) run higher than the analog figures (95 to 150 g) for the same threads, so the same thread does not read the same on every gauge. The bobbin figures agree far better: every gram-force source for metal cases falls between 18 and 35 g, and the Madeira and TOWA ranges meet at 22 g, which is why it makes a sensible starting point.

How to take a reading you can trust

How you pull changes the reading. Pulling fast reads high: AllBrands' TOWA digital listing warns that pulling too quickly gives artificially elevated readings. Melco's instruction is to pull "at approximately an inch per second."

  1. Clean the case first. Lint under the spring skews the reading; see cleaning the bobbin area.
  2. Load the bobbin you will stitch with. Echidna notes that different brands of bobbin thread give different tensions. If you switch between prewound and self-wound bobbins, measure both.
  3. Thread it under the spring, out of the pigtail. The TOWA instructions take the thread out of the pigtail guide for the reading. Seat the case in the gauge slot.
  4. Route it over the gauge. On a TOWA case gauge, wrap the thread around the two pulley wheels and the hook end.
  5. Pull steadily and read. About an inch (25 mm) per second, without stopping, and read the number while the thread is moving.
  6. Turn the screw in small steps. Clockwise tightens. Mark the start position, turn a little, read again.
  7. Confirm on fabric. Run an I-test: Madeira's target for a satin is one third bobbin, two thirds top thread color on the underside.

Set the bobbin first or the top first?

With a gauge, the bobbin first. Madeira's instruction is to "set your bobbin tension correctly prior to managing your top tensions." That looks like the opposite of the usual advice to change the top first, but without a gauge, turning the bobbin screw is a guess, so you try the reversible top side first. With a gauge, the bobbin becomes a measured baseline for every top tension change after it.

On a multi-needle machine one bobbin serves every needle, so a measured case lets you balance each needle's top tension separately, the method in embroidery thread tension. If bobbin thread shows on all needles at once, the case is the suspect; on one needle only, the top thread path is (see bobbin thread showing on top).

Set the bobbin, stitch a test, then work on top tension: change one thing at a time, the core rule of the Stitch-Out Tuning Method.

Caps and heavy goods

Every source with a cap figure gives 25 g: Madeira, the TOWA analog text and the TOWA digital guideline. Treat 25 g as a ceiling, not a target, and go there only if the cap underside shows too little bobbin on an I-test. Hooping matters more on caps; see caps and hats.

If you keep a separate case for caps, set it once and label it rather than turning one screw back and forth.

Melco and home machines: different gauges, different numbers

Melco

Melco's support answer for the EMT16, EMT16 Plus, Bravo, EMT16x, XT and XTS says the tension "should be between 250 and 300," measured on Melco's own gauge (PN 34746) or its digital gauge (PN 35583). No unit is given. Use it on a Melco with a Melco gauge; no source equates it with the TOWA grams above.

Drop-in home machines

The TOWA case gauges do not fit drop-in cases: AllBrands' class 15 listing explicitly excludes them, and the M-size listing says it is for jumbo cases, not drop-in ones. Echidna, an Australian sewing retailer, sells a push-pull gauge with the thread tied to its hook and says "typically, between 30 and 50 grams will work well for most machines." In its home machine example, 50 g gave the 30 to 60 percent bobbin it recommends under a satin; 75 g was "quite tight." A different gauge and pull, so no contradiction with the TOWA figures. On a drop-in machine the I-test and your manual come first; bobbin thread and prewound bobbins covers the thread side. On a Brother combination machine, adjust only the case with no color on the screw, 30 to 45 degrees per step, never the green screw case: see Brother bobbin case: green screw vs no color.

When these numbers stop applying

  • Your machine maker gives a figure. Use it. The Madeira guidelines say themselves that the numbers "may need to be adjusted up or down depending upon your specific machine."
  • Your bobbin thread is not the usual fine polyester. The figures are for fine bobbin thread (Tajima's row names polyester 120/2). A heavier thread in the bobbin needs its own reading and its own test. See thread weights.
  • The reading is right but the stitch-out is not. Then it is not the spring: check top threading, needle and lint, or see bird nesting for thread piling under the plate.

The gauge does not replace the stitch-out. It makes the bobbin repeatable.

Frequently asked questions

What should bobbin tension be in grams for embroidery?

On a TOWA-type case gauge, 18 to 22 g for flat goods by Madeira's guide, or 22 to 25 gf by the TOWA digital guideline, and up to 25 g for caps. Start at 22 g if you have no machine-specific figure, then confirm with an I-test.

Is bobbin tension 180 to 220 grams or 18 to 22 grams?

The same setting. The TOWA gauge text gives 180 to 220 and then says that on a gauge shown in units of tens it is 18 to 22 grams. Only 18 to 22 is grams: 180 g would pull harder than the 100 to 150 g top thread tension the same makers give.

What bobbin tension for caps?

Up to 25 g on a TOWA-type gauge, the figure Madeira and the TOWA guidelines give. Treat it as a ceiling and go there only if the I-test on the cap shows too little bobbin.

Can I use a TOWA gauge on a drop-in bobbin machine?

Not the TOWA case gauges: their listings exclude drop-in cases. A push-pull gauge such as Echidna's works on home machines, but it reads differently: Echidna gives 30 to 50 g for most machines. Check against your manual and an I-test.

Sources and further reading

Found something wrong or out of date? Tell us and we will fix it.