Brother bobbin case: green screw vs no color on the screw
Brother ships its sewing and embroidery machines with two bobbin cases, and the usual advice is that one is for sewing and one for embroidery. Brother's own manual draws the line somewhere else: at the bobbin thread. Here is which case goes with which thread, how to tell them apart, and how far to turn the one you may adjust.
Quick answer
Use the green screw case for sewing and for embroidery with the 60 weight bobbin thread that came with the machine, and never adjust it. Use the case with no color on the screw for prewound bobbins or any other bobbin thread. Adjust only its slotted (-) screw, 30 to 45 degrees per step with the bobbin out, and never the Phillips (+) screw.
On this page
- Key takeaways
- What the two bobbin cases are
- Which case for which job
- Green for sewing, no color for embroidery? Not quite
- Which bobbin thread goes with which case
- Worked example: switching to prewound bobbins
- How far to turn the screw
- When the top thread loops
- The gray case is for bobbin work
- What this does not cover
Key takeaways
- Green screw: the standard case. Use it for sewing and for embroidery with the 60 weight bobbin thread that came with the machine. Never turn its screw.
- No color on the screw: a tighter case for prewound bobbins and any other bobbin thread. It has a dark mark inside the cavity, and it is the one you may adjust.
- Turn only the slotted (-) screw, 30 to 45 degrees per step. That is 5 to 7.5 minutes on a clock face. Never turn the Phillips (+) screw.
- Clockwise when bobbin thread shows on top. Counterclockwise when the top thread loops and no bobbin shows underneath. Take the bobbin out first.
- A gray case, where your machine has one, is for bobbin work with thick thread or ribbon. It is not for normal embroidery.
On a Brother sewing and embroidery machine, use the green screw bobbin case with the 60 weight bobbin thread that came with the machine, and the case with no color on the screw for prewound bobbins or any other bobbin thread. Only the no-color case is adjusted, 30 to 45 degrees of its slotted screw at a time.
What the two bobbin cases are
A bobbin case is the small holder the bobbin sits in, under the needle plate. The bobbin thread passes under a flat spring on the case. How hard that spring presses is the bobbin tension: the drag on the bobbin thread while the top thread pulls it into each stitch.
Each case has two screws. The slotted screw has one straight slot, which Brother marks with a minus sign (-). It sets the spring pressure, and it is the only one you adjust. The Phillips screw has a cross (+). Brother says moving it "may result in damage to the bobbin case, rendering it unusable."
The color is on the slotted screw. Brother's manual describes the cases:
- Standard case, green marking on the screw. The case "originally installed in the machine." Brother says: "Do not adjust the tension screw on this bobbin case with the green marked screw." Sewing Parts Online, a parts retailer, says the green is Loctite on the screw threads, so the factory setting cannot drift.
- Alternate case, no color on the screw. Brother says it "is set with tighter tension for embroidery with different weights of bobbin threads and a variety of embroidery techniques." It has "a dark colored mark on the inside of the bobbin cavity," and its screw "can be adjusted if necessary."
Which case for which job
Every row is a ruling from Brother's manual pages, linked below.
| What you are doing | Case | Turn the screw? | Brother's words |
|---|---|---|---|
| Sewing utility stitches | Green screw | No | "Use the green marked bobbin case when performing utility stitch sewing" |
| Embroidery with the bobbin thread that came with the machine (60 wt) | Green screw | No | Recommended "for embroidering with included 60 weight bobbin thread" |
| Embroidery with prewound bobbins | No color | Only if a test calls for it | "Bobbin case (for prewound or other embroidery bobbin threads)" |
| Embroidery with any other bobbin thread | No color | Only if a test calls for it | For "substitute embroidery bobbin threads (other than what is packaged with your machine)" |
| Bobbin work: thick thread or ribbon wound on the bobbin | Gray bobbin work case | Yes, same 30 to 45 degree steps | "Be sure to use the bobbin case (gray) when creating bobbin work" |
Green for sewing, no color for embroidery? Not quite
The common shorthand is that green is the sewing case and no color is the embroidery case. That is half right. Brother recommends the green case for sewing and for embroidery, as long as the bobbin holds the thread from the box. What decides the swap is the bobbin thread, not the mode. Embroidering with the thread that came with the machine? Keep the green case in.
The opposite mistake circulates too. Sewing Parts Online says the alternate case "can also be used for both sewing and embroidery." Brother says to use the green case for utility stitch sewing. Follow Brother: the no-color case is set tighter.
Which bobbin thread goes with which case
Brother's rule is about where the thread came from, not only its weight. The green case is matched to the included 60 weight bobbin thread. The no-color case is for anything else: prewound bobbins, another brand, another weight. Another brand's 60 weight is still a "substitute" in Brother's words.
Weight numbers run backwards: 90 weight is finer than 60 (see thread weights).
First check that a prewound fits. Brother's own 90 weight prewound bobbins (PWB350) are size 11.5 for its embroidery-only machines. Brother's product page marks them "Not for use with Brother sewing or embroidery/sewing combo models." Use the bobbin size your manual names; Bobbin thread and prewound bobbins covers sizes and types.
Worked example: switching to prewound bobbins
Take a Brother combination machine with the green case installed. Suppose you have run out of the bobbin thread from the box, and you switch to prewound bobbins in the size your manual lists. Walk it through Brother's pages.
- Find the right case. Look at the slotted screw. A green dab means the standard case. No green, plus a dark mark in the bottom of the cavity, means the alternate case.
- Fit the no-color case. Brush out the bobbin area while the case is out (see cleaning the bobbin area).
- Stitch a test before you touch the screw. The case is already set tighter than the green one, so it may need nothing. An I-test shows the balance. Brother's target is "Upper thread slightly appears on the wrong side of fabric."
- Read the front. Suppose bobbin thread shows slightly on the right side. Brother calls that "Bobbin Thread Is Too Loose."
- Take the bobbin out and make one step. Turn the slotted screw clockwise, 30 to 45 degrees: from 12 o'clock to between the 1 and halfway to the 2.
- Test again. Still showing: one more step. If the top thread now lifts or loops on the front and no bobbin shows on the back, that step went too far. Turn back counterclockwise by one step.
- Stop if the screw is stiff. Brother: "do not use force."
How far to turn the screw
Brother's figure is "approximately 30-45 degrees" per adjustment, clockwise to tighten and counterclockwise to loosen. One minute on a clock face is 6 degrees, so that is 5 to 7.5 minutes. That is one twelfth to one eighth of a turn.
Sewing Parts Online tells readers to work in 15-minute steps. Fifteen minutes is a quarter turn, 90 degrees: twice Brother's largest step. On this Brother case, use Brother's figure. Our general bobbin tension guide uses smaller nudges, for cases with no maker figure.
Brother publishes no gram reading for these cases. The case gauges in our bobbin tension gauge guide are for metal multi-needle cases, so here the stitch test is the measure.
When the top thread loops
Brother's sign of a too-tight bobbin has two parts: the top thread loops on the front, and no bobbin thread shows on the back. Only then is the fix a counterclockwise step. If the front loops but bobbin still shows on the back, the bobbin is not too tight by Brother's test. For "some looping in the upper thread," Brother's embroidery page names another fix: the included embroidery needle plate cover, pushed on as far as it goes. Other causes are in loops on top. If bobbin thread still shows on the front after a step or two, work through bobbin thread showing on top before turning further.
The gray case is for bobbin work
Bobbin work means winding a thread or ribbon too thick for the needle onto the bobbin and stitching from the wrong side of the fabric, so the thick thread lies on the face. Brother's bobbin work manual adds a third case for it, in gray, and lists No. 5 or finer hand embroidery thread, woven ribbon, and fine ribbon of 3.5 mm or less. The gray case adjusts like the no-color one: the slotted screw, 30 to 45 degrees per step, never the Phillips screw. Brother adds that turning it "may push up the spring plate." Press it back down below the top of the case. Ribbon runs without tension: not under the spring.
Keep it for bobbin work only. Brother says it "cannot be used for sewing in any way other than bobbin work," and that any other case used for bobbin work can tangle the thread or damage the machine.
What this does not cover
This page follows Brother's manuals for combination sewing and embroidery machines that come with the green and no-color cases. Not every Brother has them: the NX2000 bobbin work manual calls that machine's standard case black. If neither of your cases has a green screw, follow your own manual. Embroidery-only models and the multi-needle PR series are not covered here. Multi-needle machines balance each needle against one bobbin; see embroidery thread tension. Brother gives no total number of turns for the no-color screw, so the stitch test tells you when to stop. Forced or turned too far, Brother warns, the case "may not maintain proper tension." Change one thing at a time, as in the stitch-out tuning method.
Frequently asked questions
Can I adjust the green screw bobbin case?
No. Brother's manual says not to adjust the tension screw on the green marked case. Sewing Parts Online explains that the green is Loctite on the screw threads, which locks the factory setting. If you need a different tension, swap to the case with no color on the screw.
Which Brother bobbin case do I use for prewound bobbins?
The case with no color on the screw. Brother's manual heads it "for prewound or other embroidery bobbin threads." Stitch a test first, since it is already set tighter, and adjust only if the test calls for it. See bobbin thread and prewound bobbins.
How much should I turn the bobbin case screw on a Brother?
About 30 to 45 degrees per step, Brother's figure: 5 to 7.5 minutes on a clock face. Turn the slotted (-) screw clockwise to tighten and counterclockwise to loosen, with the bobbin out, and test after each step. Never turn the Phillips (+) screw.
Can I sew with the no-color bobbin case?
Brother says to use the green marked case for utility stitch sewing. The no-color case is set tighter for embroidery bobbin threads, so put the green case back before you sew seams.
How do I tell the two Brother bobbin cases apart?
The standard case has a green marking on its slotted screw. The alternate case has no color on the screw and, in Brother's words, "a dark colored mark on the inside of the bobbin cavity." A gray case, if you have one, is the bobbin work case.
Sources and further reading
- Brother: Embroidering Attractive Finishes (operation manual) Green case for sewing and the included 60 weight bobbin thread, do not adjust; no-color case set tighter for prewound and other bobbin threads, dark mark in the cavity; embroidery needle plate cover for upper thread looping
- Brother: Adjusting the Bobbin Case (with No Color on the Screw) Green case for utility stitch sewing; no-color case for substitute bobbin threads; slotted screw 30 to 45 degrees per step; correct, too loose and too tight signs; never the Phillips screw; remove the bobbin; do not force
- Brother: Bobbin Work instruction manual (NX2000) Gray bobbin work case only for bobbin work; No. 5 or finer thread, ribbon 3.5 mm or less; slotted screw 30 to 45 degrees; spring plate may lift; standard case black on this model
- Brother 882-W01 operation manual, page 226 (ManualsLib) An older Brother manual with the same two cases: do not adjust the green marked screw; alternate case tighter, dark mark in the cavity
- Brother USA: PWB350 prewound embroidery bobbins 90 weight, size 11.5, for embroidery-only machines; not for sewing or embroidery/sewing combo models
- Sewing Parts Online: Know your bobbin cases Loctite on the green screw; alternate case dot may be purple, another color or absent; 15-minute adjustment steps
Found something wrong or out of date? Tell us and we will fix it.