Fusible stabilizer iron temperature: what setting to use

Iron settings for fusible no-show mesh, cutaway and tearaway from Floriani, OESD, PFAFF, HUSQVARNA VIKING and Madeira in one table, the iron dial converted to degrees, and what bubbling, glue on the plate and shine mean.

Updated 9 min read Reviewed against our editorial standards

Quick answer

Use a dry iron at about 250 to 270°F (120 to 130°C): the low end of two dots, often labeled silk or wool. Floriani says 260°F. Put the shiny glue side on the wrong side of the fabric and press from the fabric side or through a press cloth, a few seconds per spot (Madeira: 5 seconds). Never go past the fabric's care label.

On this page
  1. Key takeaways
  2. Iron settings by product
  3. Silk setting at 260°F, or medium to high?
  4. Convert the iron dial to a temperature
  5. Which side to iron from
  6. Fuse it, step by step
  7. Bubbling, not sticking, glue on the iron, shine
  8. How to release it after stitching
  9. Worked example: a polyester polo labeled one dot
  10. What this does not cover

Key takeaways

  • Fuse embroidery stabilizer with a dry iron at about 250 to 270°F (120 to 130°C). On a dotted dial that is the low end of two dots, the setting most irons label wool or silk.
  • Put the shiny glue side on the wrong side of the fabric. Keep the iron off the glue: press from the fabric side, as Floriani says, or through a press cloth.
  • Press a few seconds per spot and lift the iron. Do not slide it. Madeira gives 5 seconds for its fusible tearaway; no maker of pre-hoop mesh gives a time.
  • "Silk setting, 260°F" is right. "Medium to high" is a dial phrase with no number, and it can run past every figure a maker publishes.
  • To remove it after stitching, warm it again at the same setting, peel it back to the stitches and trim.

Set a dry iron to about 250 to 270°F (about 120 to 130°C). Lay the shiny glue side against the wrong side of the fabric. Press each spot for a few seconds, from the fabric side or through a press cloth. That holds for fusible no-show mesh, fusible cutaway and fusible tearaway. Floriani gives 260°F, "Silk Setting," for all three of its fusible types, with a dry iron for its mesh and cutaway. If the stabilizer will not stick, press longer first. Then raise the heat slowly, never past what the fabric's care label allows.

First, the terms. A fusible stabilizer is a stabilizer with heat-activated glue on one side. You iron it to the back of the fabric before you hoop. The glue holds the fabric still, so a knit cannot stretch out of shape while you hoop and stitch. It comes in the same families as plain backing: no-show mesh (a sheer, soft cutaway), heavier fusible cutaway, and fusible tearaway. A dry iron means the steam is off. The dots on an iron's dial are the same dots as on a care label: one, two or three, each with a top temperature.

Iron settings by product

Every setting below is the maker's own wording, with the number converted where the maker gives one. Where a maker gives nothing, the cell says so.

Fusible stabilizer iron settings, as each maker publishes them
ProductMaker's settingAs a temperatureTimeSteamWhat the iron touches
Floriani No Show Nylon Mesh Fusible (1.5 oz)Low to medium, "260°F (120°C) Silk Setting"260°F is about 127°CNot givenDryThe fabric, not the stabilizer; press cloth if needed
Floriani Medium Cutaway Fusible (2.0 oz)Low to medium, "260°F (120°C) Silk Setting"About 127°CNot givenDryThe fabric, not the stabilizer
Floriani Heat N Sta fusible tearawayLow to medium, "260°F (120°C) Silk Setting"About 127°CNot givenNot statedThe fabric, or a press cloth
OESD Fusible PolyMesh CutAway"Medium warm iron." "Do not overheat."No number givenNot givenNot statedThe stabilizer (item wrong side up, mesh on top)
PFAFF and HUSQVARNA VIKING Fusible Whisper Web (polyester no-show mesh)"Between medium and high," using heat right for the fabricNo number givenNot givenNot statedNot stated
Madeira CMX fusible tearawayIron: "medium heat (two dots; with steam)." Press: 104 to 132°C, 2 to 4 barTwo dots is at most 160°C (320°F); press 219 to 270°FIron 5 s; press 4 to 6 sYesNot stated; coated side down
Madeira Weblon Plus Fusible cutaway (polyamide)Hot and long enough to bond "slightly" but not "completely melt." Low pressure.No number givenNot givenCan be used to adjust the bondNot stated; sheen side down
Madeira E-Zee Weblon No Show Fusible 1.65 oz (US)"250° to 260°"121 to 127°C (read as °F)10 to 20 sNot statedNot stated; shiny dot side down
AllStitch Cover-A-Stitch (finisher)250 to 270°F, "Wool setting for irons"121 to 132°CAbout 15 sNot statedNot stated; fusible side to the garment

The last two rows are not pre-hoop stabilizers. Madeira USA sells E-Zee No Show Fusible as a "backing finisher," fused over the back of finished stitches, and Cover-A-Stitch is the same kind of cover. They show what heat this kind of iron-on glue is made for. Madeira's US sheet prints "250° to 260°" with no unit. It must be Fahrenheit: 250°C is past the 210°C top of the hottest iron setting. Our page on cover backing for itchy stitches has the full settings for finishers.

Floriani prints its figure as "260°F (120°C)", but 260°F is about 127°C. Floriani calls it "a starting point," since "all irons heat differently."

Silk setting at 260°F, or medium to high?

Two answers circulate. Floriani says 260°F, the silk setting. PFAFF and HUSQVARNA VIKING say "between medium and high." Follow Floriani, for three reasons.

  • It is the only one with a number. "Medium" and "high" mean different heats on different irons. 260°F means one thing.
  • Every published number agrees with it. Floriani's 260°F, Madeira's 250 to 260° and Cover-A-Stitch's 250 to 270°F all fall between about 120 and 130°C. Madeira's press range for CMX, 104 to 132°C, tops out there too. None of the makers here publishes a higher number.
  • "High" can melt the stabilizer. Floriani's mesh is nylon, and so is Madeira's Weblon Plus (polyamide is nylon). GINETEX puts nylon at one dot, a sole plate of at most 120°C. OESD warns "do not overheat," and Madeira asks for a bond that does not "completely melt."

"Medium to high" persists because it is printed on the package. The same line says to use the right heat for the fabric, so read it as a ceiling, not a target. Start at 260°F, and go up only if the stabilizer will not hold.

Convert the iron dial to a temperature

Most irons show fiber names or dots, not degrees. GINETEX, the body behind the care symbols, defines each dot by its top sole plate temperature. Our page on thread wash and iron temperatures uses the same scale.

Iron dots, their GINETEX limits, and where fusible stabilizer sits
DialGINETEX top temperatureDial label (GINETEX)For fusible stabilizer
One dot120°C (248°F)Polyacryl, polyamide (nylon), acetateThe top of this band meets Floriani's 120°C. Fabric labeled one dot gives you no room to go higher.
Two dots160°C (320°F)Wool, silk, polyester, viscoseThe working band. Use the low end, about 120 to 130°C. Madeira's CMX iron setting is two dots.
Three dots210°C (410°F)Cotton, linenAbove every published fusible figure. Not needed.

GINETEX puts silk and wool on the same two dot setting, so Floriani's "silk" and AllStitch's "wool" name the same band. Neither word is a temperature. Two dots can run up to 160°C, so set the dial just past one dot, not in the middle of two.

The fabric sets the ceiling. GINETEX says to choose the iron temperature from the care label, not the fiber content. On a two dot fabric, you have room to go up if the stabilizer will not hold. On a one dot fabric, 120°C is both the fusing figure and the limit.

Which side to iron from

The makers agree on the glue side: shiny side down, on the wrong side of the fabric. PFAFF calls it "the shinier side"; Madeira describes a "slight sheen" or "shiny dots." They differ on where the iron goes.

  • Floriani: iron on the fabric. "The iron surface should touch the fabric, NOT the stabilizer." Mesh is open, so glue can come through it onto the plate. Pressing from the fabric side keeps the plate clean.
  • OESD: iron on the stabilizer. Lay the item wrong side up, put the mesh on top, shiny side down, and press it.

Both work, and a press cloth covers the risk in each. On cotton or another matte fabric, use Floriani's way. On a shiny or dark polyester knit, use OESD's layout with a press cloth over the mesh. The iron then touches neither the face nor the glue.

Fuse it, step by step

  1. Read the care label. Its dots are your ceiling. If it says do not iron, use another hold from adhesives and fusibles.
  2. Empty the steam. Floriani says a dry iron. Set the dial just past one dot, or 260°F on a digital iron.
  3. Cut the piece big enough. PFAFF says at least 1 in past the hoop on all four sides. Floriani says at least 1 in larger than the hoop, and OESD about 2 in larger.
  4. Find the glue side. Tilt it in the light. The shiny side goes against the wrong side of the fabric.
  5. Press, do not iron. Set the iron down for a few seconds, lift it and move to the next spot. Madeira's CMX figure is 5 seconds. Sliding the iron stretches a knit and pushes the stabilizer off grain.
  6. Let it cool, then lift a corner. PFAFF says the bond need not be permanent, since it will be peeled back later.
  7. Hoop and stitch. OESD says the stabilizer must fill the whole hooped area. For a dense design, OESD and PFAFF both suggest a second layer. T-shirts and knits has the rest of the knit setup.

Bubbling, not sticking, glue on the iron, shine

It will not stick, or lifts as soon as it cools
Too little heat or time for that iron. Madeira says the bond is controlled by "temperature, pressure, iron time and steam." Press longer first, then raise the heat slowly, as Floriani says, up to the label's limit. Madeira notes that fabric finishes affect the bond, so some fabrics will not take it. Switch to sticky stabilizer or spray.
Bubbles or ripples after fusing
These are spots that never bonded, or a knit that was stretched while hot. A sliding iron does both. Lay the fabric flat without pulling it. Press the bubbled spots again, lifting the iron each time, and let it cool before you move it.
Glue on the iron plate
The plate touched the glue, through the open mesh or past the edge. Next time press from the fabric side or use a press cloth. To clean it, Floriani says to heat the iron to its highest setting and rub the plate firmly over a wet towel, or use an iron cleaner.
Glue dots showing on the front
Too much pressure. Madeira says to "always use low pressure to avoid glue dot marks." Let the iron's own weight do the work.
Shine on a polyester knit
The iron pressed the face of the fabric. New Mexico State University's pressing guide says to use a press cloth on the right side to prevent shine, and that too much heat, steam or pressure can flatten the surface. GINETEX says to iron shiny items with a press cloth or inside out. Use OESD's layout with a press cloth.

How to release it after stitching

A fusible cutaway or mesh is still glued to the fabric around the design. Warm it before you peel it.

  1. Lay it stabilizer side up on the ironing board, as OESD says.
  2. Warm it at the fusing setting. OESD says to reheat "with a medium warm iron to release the adhesive bond" if it does not come away easily. Floriani says to re-heat the stabilizer and peel it back gently. Do not turn the heat up for this.
  3. Peel it back to the edge of the stitches.
  4. Trim. OESD trims from the front, lifting and folding the fabric out of the way. PFAFF says to leave about 1/4 in outside the design. With two layers, trim one at a time.
  5. Tearaway tears. Floriani Heat N Sta and Madeira CMX are torn away like plain tearaway. Madeira says any residue of CMX comes out in the wash.

The release heat now lands on the stitches as well. Polyester and rayon embroidery thread are rated for two dots. Metallic thread is held to one dot, at most 120°C. Over metallic stitches, stay at Floriani's 260°F or below, and use a press cloth.

Worked example: a polyester polo labeled one dot

Take a 100% polyester performance polo. Suppose its care label shows an iron with one dot. You plan a left chest logo with Floriani No Show Nylon Mesh Fusible and polyester thread.

  1. Find the ceiling. One dot is at most 120°C (248°F). Floriani's figure is 260°F, which it prints as 120°C. So the starting point and the ceiling are the same. There is no room to go hotter.
  2. Pick the layout. Smooth polyester can shine. Lay the front wrong side up, put the mesh on it shiny side down, and cover it with a press cloth.
  3. Press. Set the iron to one dot, steam off. Press each spot a few seconds and lift. Let it cool and lift a corner to check.
  4. If it will not hold, do not raise the heat past the label. Press each spot longer. If that fails, switch to a non-fusible mesh with spray adhesive or a sticky stabilizer, as adhesives and fusibles describes.
  5. Release. After stitching, warm the mesh at the same one dot setting through the press cloth, peel it back to the stitches, and trim.

What this does not cover

These are home iron settings. Only Madeira's CMX sheet gives heat press figures, and no maker gives a time for pre-hoop mesh. Floriani says all irons heat differently, so silk on one iron is not the same heat on another. The 120 to 130°C band is where the published numbers meet, not a figure any one maker states for its whole range. PFAFF and HUSQVARNA VIKING give no number at all. For a product not in the table, use its maker's figure if it has one. Some fabrics should not be fused at all: vinyl, faux leather, velvet and other napped fabrics, coated rain shells, and anything labeled do not iron. For a rain shell, see sealing embroidery on waterproof jackets. A fusible holds the fabric still. It does not choose the backing weight for you; the stabilizer picker does that.

Frequently asked questions

What temperature do you iron fusible no-show mesh?

About 260°F (127°C) with a dry iron, which Floriani calls the silk setting. The published figures for this kind of glue run from about 250 to 270°F (120 to 130°C). OESD gives no number, only "medium warm" and "do not overheat." If it will not stick, press longer, then raise the heat slowly, never past the fabric's care label.

Should I use steam to fuse embroidery stabilizer?

Not on mesh. Floriani says a dry iron for its No Show Mesh and Medium Cutaway Fusible. Madeira's CMX fusible tearaway is the exception: its sheet says two dots with steam, for 5 seconds.

Which side of fusible stabilizer goes on the fabric?

The shiny side. PFAFF calls it the shinier side and Madeira describes a slight sheen or shiny dots. Put it against the wrong side of the fabric, then press from the fabric side, as Floriani says, or through a press cloth.

Why won't my fusible stabilizer stick?

Too little heat or time for your iron, or a fabric finish that resists the glue, which Madeira says affects the bond. Press each spot longer, then raise the heat slowly up to the care label's limit. If it still lifts, use sticky stabilizer or spray adhesive.

How do you remove fusible stabilizer after embroidery?

Warm it again at the same setting, stabilizer side up, then peel it back to the edge of the stitches and trim. OESD and Floriani both say to reheat it. Fusible tearaway, such as Floriani Heat N Sta or Madeira CMX, is simply torn away.

Sources and further reading

Found something wrong or out of date? Tell us and we will fix it.