Water-soluble stabilizer brittle or crispy: is it still usable?

Why PVA film goes crispy in dry air and limp in damp air, how to test an old roll in five minutes, and how to restore and store it.

Updated 7 min read Reviewed against our editorial standards

Quick answer

Usually, yes. Crispy water-soluble stabilizer has dried out; it has not expired. PVA film needs a little water from the air to stay bendy, and dry or cold air makes it brittle. Seal it in a plastic bag with the air squeezed out and leave it for a while: Sulky says it usually returns to its proper feel. Then crease a strip. If it folds without cracking, use it.

On this page
  1. Key takeaways
  2. Why PVA film goes brittle
  3. Crispy or limp: what each one means
  4. Is it still usable? Test it in five minutes
  5. How to restore brittle water-soluble stabilizer
  6. How to store water-soluble stabilizer
  7. Worked example: a partial bolt of Solvy from a friend
  8. What this does not cover

Key takeaways

  • Brittle or crispy water-soluble stabilizer has dried out. It has not expired. Sulky calls old Solvy "climate sensitive, but still usable."
  • PVA, the plastic most washaway is made of, needs a little water from the air to stay bendy. A Clorox patent says it turns brittle below about 15% relative humidity, even at 20°C (68°F). Cold makes it worse.
  • Too much damp does the opposite. The film goes limp and weak.
  • To bring it back, seal it in a plastic bag with the air squeezed out and leave it for a while. Sulky says it usually returns to its proper feel.
  • Store it in its clamshell pack or a sealed bag, indoors. Never mist it with water, and do not add a drying packet.

Yes, brittle water-soluble stabilizer is usually still usable. If it has gone crispy, it has dried out. It has not gone bad. A Sulky reader asked about an old partial bolt of Solvy, and Sulky's answer was that the film "can get a little crispy when stored in dry climates and not properly covered." Stored in a sealed plastic bag with the air squeezed out, it usually goes back to its proper feel. Sulky's verdict: "climate sensitive, but still usable."

First, the terms. Water-soluble stabilizer, also called washaway, is a stabilizer that dissolves in water, so nothing is left in the finished piece. Most of it is made of polyvinyl alcohol (PVA), a plastic that dissolves in water. Sulky says its Solvy films are PVA film. Madeira's data sheet lists Avalon Plus as 100% PVA. It comes in two main forms. Film is a clear plastic sheet, like Solvy. It is the usual topper, the layer laid over a towel so stitches do not sink into the loops. Fibrous washaway is a nonwoven sheet that looks more like paper or fabric. Madeira's sheet calls Avalon Plus a nonwoven, 300 microns thick. Brittle means the sheet cracks or snaps when you bend it, instead of folding.

Why PVA film goes brittle

PVA is hygroscopic: it pulls water out of the air and holds it. That water does a job. A plasticizer is anything in a plastic that lets it bend instead of crack. In PVA, water is the main one. A Clorox patent on PVA film puts it plainly: PVA "readily absorbs water from the atmosphere. The absorbed water acts as a plasticizer, and assists in preventing brittleness."

Take that water away and the film stiffens. The same patent says PVA becomes brittle "at low temperatures and low relative humidity," with "very little impact resistance." It gives one number: "Even at 20° C., polyvinyl alcohol becomes brittle when the relative humidity is less than about 15%." Relative humidity is how much water the air holds, compared with the most it could hold at that temperature.

Makers add softeners, but those work through water too. A du Pont patent names glycerine and sorbitol. They are humectants, which means they hold water. Du Pont says "the water absorbed by the humectant is actually the plasticizer," so these films still "become brittle under conditions of low humidity."

There is a second failure, at the other end. Du Pont says high humidity "likewise leads to low strength because of excessive water absorption by the film." Sulky reports the same thing in its own words: Solvy can get "wimpy" in a humid climate. So PVA does not store like thread, where the advice is mainly to keep it dry. It has a comfortable middle, and it can leave it in either direction.

The thinnest film shows it first. Sulky says Solvy gets crispy "especially the lightest weights." That is the topper film, which Sulky says is "almost always used as a topper." Super Solvy, by Sulky's account, is twice as thick as Solvy.

Crispy or limp: what each one means

What old water-soluble stabilizer tells you, and what to do
What you feelCauseWhat to doSource
Crackles, cracks or snaps when you crease itToo drySeal it in a bag with the air out, then test againSulky; Clorox patent
Crisp just after a cold garage or carColdLet it reach room temperature before you judge itClorox patent
Limp, floppy, tears too easilyToo dampSeal it in a bag with the air out, then test againSulky; du Pont patent
Heat-away stabilizer feels offHeat-away is a different productLess affected by climate; bag it anywaySulky

Two answers circulate about old washaway. One says brittle film has expired, so throw it out. The other says it is fine. The second is right, with one step added: bring it back before you use it. None of the makers we read gives a shelf life in years. Asked straight out whether Solvy on the bolt has one, Sulky answered with climate, not age. The "expired" answer persists because crisp film looks ruined, and because the thin topper film is the one that changes most.

Is it still usable? Test it in five minutes

  1. Warm it first. If the roll or pack came from a cold place, leave it indoors until it is at room temperature. Cold PVA is brittle, so a cold test tells you nothing.
  2. Cut two strips. Take one from the outer wrap of the roll and one from deeper inside. Sulky ties crispness to film "not properly covered," so the outside of an open roll dries first.
  3. Crease each strip. Fold it sharply and press the fold flat. Good film folds and holds the crease. Brittle film cracks along the fold or snaps.
  4. Drop a scrap in water. Use a glass of tap water. Madeira gives Avalon Plus about 60 seconds at about 20°C, which it notes is tap water temperature. Sulky says Solvy dissolves in water anywhere from 32 to 200°F (0 to 93°C). A scrap that dissolves will rinse out of your project.
  5. Decide. If both strips fold, use it. If the outer strip cracks but the inner one folds, cut off the outer wraps. If both crack, restore the roll as below, then test again.

Check the job, too. A topper only has to hold pile down while the stitches lock, as towels and terry explains, so it asks less of the film. A washaway backing for lace carries the whole design. Our page on free-standing lace stabilizer covers what that needs. Do not trust a doubtful sheet there.

How to restore brittle water-soluble stabilizer

Sulky's fix is simple: store the film "in a sealed plastic bag for a bit (with the air squeezed out)."

  1. Bag it. Put the roll, pack or sheets in a plastic bag that seals, such as a zip bag.
  2. Squeeze out the air before you close it, as Sulky says.
  3. Leave it indoors. Use a room you live in, not a garage. The Clorox patent ties brittleness to cold as well as dry air.
  4. Test again. Sulky gives no time, only "for a bit." So crease a strip before you hoop it, and give it longer if it still cracks.

How to store water-soluble stabilizer

Sulky's storage rule covers every stabilizer but singles out this one: "Keep all stabilizers in their clamshell packs, when possible. This is particularly important with water solubles." A clamshell is the clear plastic box many stabilizers are sold in. If yours came without one, use a sealed plastic bag with the air squeezed out.

  • Keep it covered. Put the roll back in its pack, or bag it, after each use. An open roll on a shelf is what Sulky means by "not properly covered."
  • Keep it indoors, not in a garage, attic or car. Our page on keeping a machine in a cold garage covers the garage itself.
  • Let the bag do the work. A sealed bag keeps the film away from both dry air and damp air. That is why one rule fixes both crispy and limp film.
  • Heat-away is less fussy. Sulky says it "is not as affected by climate," but a plastic bag is still "a good idea." See washaway vs heat-away for when to use each.

Worked example: a partial bolt of Solvy from a friend

Take the case Sulky answered. Suppose someone gives you a partial bolt of lightweight Solvy. It has sat open on a shelf through a dry winter, and the outer wrap crackles when you unroll it.

  1. Name the product. Lightweight Solvy is topper film, so Sulky says it will almost always feel softer than heavier Solvy products. Soft is normal. Cracking is not.
  2. Warm and test. Leave it in the house until it is at room temperature. Then crease a strip from the outside and one from a few turns in. Suppose the outer strip cracks and the inner one folds.
  3. Trim the outside. Cut off the outer wraps that crack. The open roll was "not properly covered," and the outside took the dry air first.
  4. Bag the rest and test again. Seal the roll with the air squeezed out, as Sulky says. When a fresh strip folds and a scrap dissolves in tap water, use it as a topper on your next towel.

If every strip still cracks after time in the bag, keep it for light topper jobs and buy fresh film for backing and lace.

What this does not cover

No stabilizer maker we read gives a shelf life, a storage temperature or a humidity range for its water-soluble products. The one number here, about 15% relative humidity at 20°C, comes from a Clorox patent on PVA film for packaging, not from a stabilizer maker. Stabilizer film may have its own softeners, and no maker publishes them. Sulky's restore method gives no time and says the film "usually" recovers, not always. The sources speak mostly about film. Fibrous washaway such as Avalon Plus is the same PVA, but no source here describes it going brittle. Sticky-backed washaway is not covered. Film that got wet and dried into a stiff lump is not covered either. If in doubt, test a scrap in a small stitch-out before you trust it with a project. For which washaway suits which job, use the stabilizer chart.

Frequently asked questions

Does water-soluble stabilizer expire?

None of the makers we read gives a shelf life in years. Asked whether old Solvy on the bolt has one, Sulky said it is "climate sensitive, but still usable." Climate, not age, decides. Test old film by creasing a strip before you use it.

Why is my Solvy brittle?

It has dried out. PVA film needs a little water from the air to stay bendy. A Clorox patent says PVA turns brittle below about 15% relative humidity, even at 20°C, and cold makes it worse. Sulky says the lightest weights get crispy first.

How do you soften brittle water-soluble stabilizer?

Seal it in a plastic bag with the air squeezed out and leave it in a room indoors for a while. Sulky says it will usually return to its proper feel. Do not mist or steam it, since it dissolves in water, and do not add a drying packet.

My washaway is limp and floppy. Is it ruined?

Probably not. Sulky says Solvy can get "wimpy" in a humid climate, and du Pont says PVA loses strength when it takes up too much water. The same sealed-bag storage usually brings it back. Test a strip before you hoop it.

How should I store water-soluble stabilizer?

In its clamshell pack, or in a sealed plastic bag with the air squeezed out, in a room you live in. Sulky says the pack is "particularly important with water solubles." Keep it out of garages and cars, and close the pack after each use.

Sources and further reading

Found something wrong or out of date? Tell us and we will fix it.