How to embroider a Carhartt jacket

Which needle and backing suit lined duck canvas, when cutaway beats tearaway, how to clamp the lining in a magnetic hoop, and where the logo goes.

Updated 8 min read Reviewed against our editorial standards

Quick answer

Use an 80/12 sharp needle, or a 75/11 sharp with a slower speed for small text. Back firm duck with one layer of medium tearaway, and switch to 2.5 oz cutaway for a sherpa lining, a dense design or hard washing. Hold the jacket in a magnetic hoop or clamp, and find the inside chest pocket first so you do not sew it shut.

On this page
  1. Key takeaways
  2. Needle: 80/12 sharp, 75/11 for fine detail
  3. Backing: tearaway on firm duck, cutaway in three cases
  4. Hooping: a magnetic hoop or a clamp
  5. The pocket hidden inside the chest
  6. Placement: left chest and back
  7. Worked example: a left chest logo on an Active Jac
  8. What this does not cover

Key takeaways

  • Use an 80/12 sharp needle on duck canvas. For small text, switch to a 75/11 sharp and slow the machine down.
  • Back firm duck with one layer of medium tearaway. Switch to 2.5 oz cutaway when the needle goes through a sherpa lining, when the design is dense, or when the jacket will be washed hard.
  • Hold the jacket in a magnetic hoop or a clamp frame. A standard hoop can let a thick jacket pop out partway through a design.
  • Find the pocket inside the chest before you hoop. If it ends up in the hoop, you sew it shut.
  • Keep a left chest logo 3 to 3.5 inches wide. On a hooded jacket, start a back design about 5 inches below the hood seam.

To embroider a Carhartt jacket, use an 80/12 sharp needle, one layer of medium tearaway behind the duck, and a magnetic hoop or clamp frame. That is the advice of SanMar, a wholesaler that sells Carhartt to decorators. For small text or fine detail, SanMar drops to a 75/11 sharp and slows the machine down. Before you hoop, find the pocket hidden inside the chest so you do not sew it shut.

Most Carhartt work jackets are made of duck canvas, and cotton duck is "a heavy, plain woven cotton fabric", woven tighter than plain canvas, says Wikipedia. The Thermal-Lined Duck Active Jac (style CTJ131, or CTTJ131 in talls) is "12-ounce, firm hand" cotton duck, per its spec sheet, and firm hand means stiff. Washed duck is the same cloth "washed for a broken-in look and feel", in the words of Wilco, a Carhartt dealer. The jackets are lined too: the Active Jac has a polyester thermal lining. The Washed Duck Sherpa-Lined Coat has sherpa, a fluffy pile fabric, in the body and quilted nylon in the sleeves. On a left chest, the needle goes through the duck, the lining and the backing all at once.

Needle: 80/12 sharp, 75/11 for fine detail

SanMar says "a larger 80/12 Sharp is best suited for this thick fabric." For "a lot of detail or small text", it would use a 75/11 sharp and slow the machine down. Its thread is 40 wt polyester. A needle's size is the width of its blade, so a 75/11 makes a smaller hole and handles fine lettering better; our embroidery needles guide explains the numbers.

The point matters as much as the size. A sharp cuts cleanly between woven threads, while a ballpoint pushes knit loops aside, which is why our needle and thread matcher keeps ballpoints for knits. One online walkthrough of a Carhartt pocket job, a HoopingStation commentary on a video, lists a 75/11 ballpoint. Duck is woven, not knit, so follow SanMar and use a sharp. Our matcher allows a 90/14 on heavy canvas, but start at 80/12 as SanMar does.

SanMar gives no speed figure. The HoopingStation walkthrough runs at 600 to 750 stitches per minute, slower than its usual speed.

Backing: tearaway on firm duck, cutaway in three cases

Two answers circulate: SanMar says "a single layer of medium weight tear away is good start", partly for ease of removal in small pockets. Embroidery Library's jacket guide uses "medium-weight (2.5 ounce) cutaway". Both are right for their own jacket. Embroidery Library never names its fabric or mentions a lining, and it opens a sleeve seam so the jacket lies flat on a home machine. SanMar is writing about heavy Carhartt fabric.

On firm duck, start with tearaway, because the cloth is stiff enough to hold the stitches by itself. Floriani's stabilizer chart puts woven cotton and denim on medium tearaway, even for solid, dense designs. Our stabilizer picker gives canvas and duck one layer of medium tearaway for a typical logo.

Cutaway wins in three cases:

  • A sherpa lining sits under the design. Sherpa is a knit and "very prone to stretching without reinforcement", says Seamwork. Floriani puts knits with medium or heavy designs on cutaway. Our picker gives polar fleece 2.5 oz cutaway at every density.
  • The design is dense, such as a full back. Our picker gives canvas two layers of medium tearaway crossed, or 2.5 oz cutaway. Floriani's answer for dense designs on wovens is an extra layer of tearaway floated under the hoop.
  • The jacket will be washed hard. Our picker switches wovens to cutaway here, because tearaway support leaves with the tearaway, and washing then lets the fabric move around the stitches.

Washed duck by itself is not one of the three. It is still plain-woven duck, softened by washing rather than turned into a knit, so back it like firm duck unless one of the cases above applies. On a sleeve with quilted nylon lining, our picker gives medium tearaway for a moderate design, and 2.5 oz cutaway with lower stitch density for a dense one.

Hooping: a magnetic hoop or a clamp

"Hooping is the biggest concern here," wrote WildWestDesigns, an embroiderer on the Signs101 forum, about Carhartt jackets. Another poster, signman315, had a CTJ131 pop out of a hoop on the first try. Their fix was to tie the hoop closed with needle and thread in two places, and they could not hoop the CTC03 for a front chest design at all. That jacket has pockets in the chest area and very rigid fabric, so they screen printed it.

SanMar says a magnetic hoop "will hold the bag much more securely and won't run into any hoop burn issues". For small pockets, it uses a clamping system instead. WildWestDesigns names Mighty Hoop magnetic hoops as the best for Carhartt. If a standard hoop has already marked the duck, see hoop burn and marks.

The lining has to be clamped flat along with the shell, or the backing side puckers. These steps follow HoopMaster's guide for thick jackets, using a 5.5 inch Mighty Hoop on a hooping fixture:

  1. Mark the first jacket of each size. Pick reference points you can find again, such as the base of the collar or the edge of a pocket. Mark the logo spot with a washable pen or a sticker.
  2. Unzip and turn it sideways. Unzip the jacket so it lies flat, and lay it sideways so the chest sits over the hoop.
  3. Hoop it. Put the lower ring in the fixture, lay the jacket on top, line up your reference points and press the top ring down until the magnets engage.
  4. Lift both rings together. Reach under and grab the bottom ring, since pulling on the top ring alone lets the jacket's weight drop the bottom ring.
  5. Check the lining. Flip the jacket over and look for puckers or bubbles in the lining. If it looks loose or uneven, hoop it again.
  6. Rotate and support. Turn the design 90 degrees to match the sideways hoop. Hold up the jacket's weight while it stitches so it does not drag on the hoop.

HoopMaster says you can hoop over most seams and zippers with a magnetic hoop. signman315 found some Carhartt seams sit where embroidery is impossible. Both can be true, so look at the seams before you promise a spot. Raise the foot for the thickness; see presser foot height.

You can also float the backing. The HoopingStation walkthrough puts the bottom frame of a 5 by 5 inch magnetic hoop inside the jacket. It slides two sheets of medium tearaway between the frame and the lining, then drops the top frame on the outside.

The pocket hidden inside the chest

The Active Jac has "two interior pockets: one zippered, one hook and loop", per its spec sheet. The Washed Duck Sherpa-Lined Coat has two interior pockets as well. A pocket behind the left chest cannot be seen from outside, and if you hoop the front with it inside the frame, the design stitches the pocket's layers together.

Find it first. The HoopingStation walkthrough puts one hand inside the pocket and the other on the outside of the jacket. It then marks the pocket's top edge on the outside with tailor's chalk or painter's tape. Feel for the sides as well, then place the design clear of the pocket, or keep the pocket out of the stitch path. After hooping, reach into the pocket. If your fingers stop short of the top, the hoop has caught it. One Signs101 poster, Billct2, buys Carhartt jackets in person so they can check the construction for obstructions first.

Placement: left chest and back

Our left chest placement figures start from where the left shoulder seam meets the collar. Men's logos center 7 to 9 inches down, 4 to 5 inches from the center front, and run 3 to 3.5 inches wide. No guide gives a separate jacket figure, because zippers, flaps and chest pockets move the usable area. So use HoopMaster's method: measure the first jacket of each size from a fixed point, then repeat it. The Sherpa-Lined Coat also has a zippered pocket on the outside of the left chest, so keep the logo clear of it.

For the back, the hood decides. On a hooded jacket like the Active Jac, start the top of the design about 5 inches below the hood seam, so the hood does not cover it. On a collared jacket, the figures in hoodie and sweatshirt placement run 6 to 9 inches from the collar seam to the design's center (Stahls), or 10 inches for men's (Embroidery Legacy). A full back is a dense design, so use the dense backing above.

Backing for a Carhartt jacket, by fabric and design
Jacket and designBackingWhy
Firm duck, thermal lining, left chest logo1 layer medium tearawaySanMar; Floriani puts wovens on tearaway
Washed duck, same designSame as firm duckStill plain-woven duck, not a knit
Sherpa lining under the design2.5 oz cutawaySherpa is a stretchy knit (Seamwork); Floriani puts knits on cutaway
Sleeve with quilted nylon liningMedium tearaway; 2.5 oz cutaway and lower density if denseOur stabilizer picker
Full back or other dense design2 layers medium tearaway crossed, or 2.5 oz cutawayOur stabilizer picker; Floriani adds a tearaway layer
Jacket washed hard2.5 oz cutawayOur stabilizer picker

Worked example: a left chest logo on an Active Jac

Take a CTJ131 Active Jac in firm duck. Suppose the logo is 3.25 inches wide and 1.75 inches tall, with a line of small lettering under it.

  1. Find the pocket. Unzip the jacket, find the interior pocket behind the left chest and tape its top edge on the outside. If the logo would overlap it, move the logo or keep the pocket out of the hoop.
  2. Place it. Start the logo's center 8 inches down from where the shoulder seam meets the collar, the middle of the 7 to 9 inch range. Put it 4 inches from the center front. Half of 3.25 inches is about 1 5/8 inches, so the logo's inner edge sits about 2 3/8 inches from the zipper line.
  3. Pick the needle. The small lettering calls for a 75/11 sharp at a slower speed; without it, an 80/12 sharp would do.
  4. Pick the backing. Firm duck, a polyester thermal lining and a moderate logo: one layer of medium tearaway.
  5. Hoop and check. Hoop it sideways in a magnetic hoop and turn the design 90 degrees. Flip it to check the lining for bubbles, then reach into the pocket to make sure it is free.
  6. Stitch and finish. Hold up the jacket's weight as it runs, then tear the backing away.

Swap in the Washed Duck Sherpa-Lined Coat and two things change. The needle now goes through sherpa, so the backing becomes 2.5 oz cutaway. And the zippered outside chest pocket takes some of the left chest, so check the logo clears it.

What this does not cover

No source here ran stitch tests on Carhartt jackets. SanMar wrote its needle and backing advice for Carhartt bags, and this page applies it to the same heavy fabric on jackets. Carhartt makes many styles, and pocket and seam layouts differ from one to the next, so check each one in hand. Flame-resistant Carhartt jackets add thread and patch rules; see embroidering FR clothing. A nylon rain shell is a different fabric; see sealing embroidery on waterproof jackets. If a jacket cannot be hooped at all, a patch is the fallback. WildWestDesigns says heat adhesive alone holds only if no side is bigger than 100 mm; past that, it must be stitched on.

Frequently asked questions

What needle do I use to embroider a Carhartt jacket?

An 80/12 sharp, per SanMar. For small text or fine detail, use a 75/11 sharp and slow the machine down. Use a sharp, not a ballpoint: duck canvas is woven, and ballpoints are for knits.

Should I use cutaway or tearaway on a Carhartt jacket?

Tearaway on firm or washed duck: one layer of medium weight for a typical logo. Use 2.5 oz cutaway if the needle goes through a sherpa lining, if the design is dense like a full back, or if the jacket will be washed hard.

Will embroidering the left chest sew the inside pocket shut?

It can. Many Carhartt jackets have interior pockets behind the chest. Put one hand inside the pocket and mark its top edge on the outside before you hoop. After hooping, reach into the pocket to make sure the hoop did not catch it.

Why does my Carhartt jacket keep popping out of the hoop?

The duck is thick and stiff, and a standard hoop cannot grip it well. Use a magnetic hoop or a clamp frame. One Signs101 poster tied the hoop closed with needle and thread in two places to keep a CTJ131 in.

Can I put a patch on a Carhartt jacket instead?

Yes. WildWestDesigns on Signs101 says heat adhesive alone works only if no side is bigger than 100 mm. A bigger patch must also be stitched down just inside its merrow edge. See heat press patches for press settings.

Sources and further reading

Found something wrong or out of date? Tell us and we will fix it.